| auszookers.com https://auszookers.com/forum/ |
|
| will this be dodgy(bull bar mod) https://auszookers.com/forum/viewtopic.php?f=5&t=4016 |
Page 1 of 1 |
| Author: | shep [ Sat Feb 07, 2009 6:10 pm ] |
| Post subject: | will this be dodgy(bull bar mod) |
i have 2 arb bars one fits well but is a bit bent and the other one is a winch bar with the mounts hacked off and some damage to one off the side bits. problem is i have a winch that i wont to fit and the bar on my car will be a bit hard to put a winch in as it is a bit not square. and it would take a fair bit of work to fit my winch bar. so what i was thinking off doing was to cut the winch bit out of the winch bar and then glue it in my non winch bar. is that problem solved? 
|
|
| Author: | atari4x4 [ Sat Feb 07, 2009 6:38 pm ] |
| Post subject: | Re: will this be dodgy(bull bar mod) |
just make sure you use metal glue 
or you could just get tails83 to make you one? http://www.auszookers.com/index.php?nam ... pic&t=3790 |
|
| Author: | ball [ Sat Feb 07, 2009 6:52 pm ] |
| Post subject: | Re: will this be dodgy(bull bar mod) |
yep dodgy do it my way, then it won't break 
|
|
| Author: | shep [ Sat Feb 07, 2009 7:07 pm ] |
| Post subject: | Re: will this be dodgy(bull bar mod) |
whats your way ball? |
|
| Author: | brendan [ Sat Feb 07, 2009 7:32 pm ] |
| Post subject: | Re: will this be dodgy(bull bar mod) |
so you want to take the midel section out and weld it into the other bar so you can use a winch? if it is how good can you weld? personaly if you dont weld for a living then i would uses any parts you welded for recovery. my winch bar is 100% bolt on |
|
| Author: | ball [ Sat Feb 07, 2009 8:06 pm ] |
| Post subject: | Re: will this be dodgy(bull bar mod) |
shep wrote: whats your way ball?
can't tell you secret fitter trick 
|
|
| Author: | guerd87 [ Sat Feb 07, 2009 8:09 pm ] |
| Post subject: | Re: will this be dodgy(bull bar mod) |
as long as the main cradle part is the piece that bolt's to your chassis shouldnt be a problem. Then just weld the outer sections to your new center |
|
| Author: | shep [ Sat Feb 07, 2009 8:16 pm ] |
| Post subject: | Re: will this be dodgy(bull bar mod) |
brendan wrote: so you want to take the midel section out and weld it into the other bar so you can use a winch?
if it is how good can you weld? personaly if you dont weld for a living then i would uses any parts you welded for recovery. my winch bar is 100% bolt on ball owns a fabrication/machine shop he does the important stuff for me. by the way ball what does a $250k cnc lathe smell like when it is on fire.
|
|
| Author: | brendan [ Sat Feb 07, 2009 8:38 pm ] |
| Post subject: | Re: will this be dodgy(bull bar mod) |
shep wrote: brendan wrote: so you want to take the midel section out and weld it into the other bar so you can use a winch? if it is how good can you weld? personaly if you dont weld for a living then i would uses any parts you welded for recovery. my winch bar is 100% bolt on ball owns a fabrication/machine shop he does the important stuff for me. by the way ball what does a $250k cnc lathe smell like when it is on fire. it smells like a $250 cnc lathe on fire 
|
|
| Author: | ball [ Sat Feb 07, 2009 8:59 pm ] |
| Post subject: | Re: will this be dodgy(bull bar mod) |
shep wrote: by the way ball what does a $250k cnc lathe smell like when it is on fire.
Like very very burnt toast 
|
|
| Author: | brendan [ Sat Feb 07, 2009 9:09 pm ] |
| Post subject: | Re: will this be dodgy(bull bar mod) |
shep wrote: brendan wrote: so you want to take the midel section out and weld it into the other bar so you can use a winch? if it is how good can you weld? personaly if you dont weld for a living then i would uses any parts you welded for recovery. my winch bar is 100% bolt on ball owns a fabrication/machine shop he does the important stuff for me. by the way ball what does a $250k cnc lathe smell like when it is on fire. it smells like a $250 cnc lathe on fire
|
|
| Author: | brendan [ Sat Feb 07, 2009 9:10 pm ] |
| Post subject: | Re: will this be dodgy(bull bar mod) |
shep wrote: brendan wrote: so you want to take the midel section out and weld it into the other bar so you can use a winch? if it is how good can you weld? personaly if you dont weld for a living then i would uses any parts you welded for recovery. my winch bar is 100% bolt on ball owns a fabrication/machine shop he does the important stuff for me. by the way ball what does a $250k cnc lathe smell like when it is on fire. it smells like a $250 cnc lathe on fire
|
|
| Author: | shep [ Sat Feb 07, 2009 9:25 pm ] |
| Post subject: | Re: will this be dodgy(bull bar mod) |
brendan wrote: shep wrote: brendan wrote: so you want to take the midel section out and weld it into the other bar so you can use a winch? if it is how good can you weld? personaly if you dont weld for a living then i would uses any parts you welded for recovery. my winch bar is 100% bolt on ball owns a fabrication/machine shop he does the important stuff for me. by the way ball what does a $250k cnc lathe smell like when it is on fire. it smells like a $250 cnc lathe on fire it is a $250000 lathe. oops sorry was.
|
|
| Author: | ball [ Sat Feb 07, 2009 9:58 pm ] |
| Post subject: | Re: will this be dodgy(bull bar mod) |
shep wrote: brendan wrote: shep wrote: brendan wrote: so you want to take the midel section out and weld it into the other bar so you can use a winch? if it is how good can you weld? personaly if you dont weld for a living then i would uses any parts you welded for recovery. my winch bar is 100% bolt on ball owns a fabrication/machine shop he does the important stuff for me. by the way ball what does a $250k cnc lathe smell like when it is on fire. it smells like a $250 cnc lathe on fire it is a $250000 lathe. oops sorry was. $2.50 now |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|