zukenutter wrote:
suzkboy wrote:
Stock sierra gears on 31s then
1L transfer for 31s
I thought the 1l transfer didn't fit.
| auszookers.com https://auszookers.com/forum/ |
|
| Jimny reduction gears https://auszookers.com/forum/viewtopic.php?f=5&t=41769 |
Page 1 of 1 |
| Author: | MikeyS [ Sat Jul 06, 2013 10:48 pm ] |
| Post subject: | Jimny reduction gears |
Hi i am going to buy 6.5:1 Sierra reduction gears for my jimny. I need to buy a 1.3L sierra T/case just wondering what type of sierra t/case will best fit this http://locktup4x4.com.au/sierra-6-5-1-r ... s-391.html ??? and do i need a driveshaft spacer?? |
|
| Author: | BertZook [ Sun Jul 07, 2013 12:20 pm ] |
| Post subject: | Re: Jimny reduction gears |
what size of tyres are you planing to run? 6.5 gears are way too low for a jimny, the % of reduction doesnt apply in the same amount for jimnys than sierras do. have a look in here viewtopic.php?f=5&t=22383 |
|
| Author: | 31zook [ Sun Jul 07, 2013 12:59 pm ] |
| Post subject: | Re: Jimny reduction gears |
6.5s will equal 37s for decent ish highway speed... |
|
| Author: | MikeyS [ Sun Jul 07, 2013 5:20 pm ] |
| Post subject: | Re: Jimny reduction gears |
I am planing on putting 31s what about the 4.5?? |
|
| Author: | suzkboy [ Sun Jul 07, 2013 5:37 pm ] |
| Post subject: | Re: Jimny reduction gears |
Stock sierra gears on 31s then |
|
| Author: | MikeyS [ Tue Jul 09, 2013 2:18 am ] |
| Post subject: | Re: Jimny reduction gears |
what do i need to fit a sierra T/case to the jimny??? 1. Shaft Spacers?? 2. front and rear tail shafts?? 3. does it matter if its a W/T or a N/T and what is W/T (wide track??) and N/T (narrow track???) |
|
| Author: | zooky08 [ Tue Jul 09, 2013 8:52 am ] |
| Post subject: | Re: Jimny reduction gears |
viewtopic.php?f=17&t=30820 |
|
| Author: | zukenutter [ Wed Jul 10, 2013 8:28 pm ] |
| Post subject: | Re: Jimny reduction gears |
suzkboy wrote: Stock sierra gears on 31s then 1L transfer for 31s |
|
| Author: | Asps91 [ Wed Jul 31, 2013 7:14 pm ] |
| Post subject: | Re: Jimny reduction gears |
zukenutter wrote: suzkboy wrote: Stock sierra gears on 31s then 1L transfer for 31s I thought the 1l transfer didn't fit.
|
|
| Author: | luke1122 [ Wed Jul 31, 2013 9:08 pm ] |
| Post subject: | Re: Jimny reduction gears |
whats needed to fit a 1l transfer to a jimny? |
|
| Author: | zukenutter [ Wed Jul 31, 2013 9:25 pm ] |
| Post subject: | Re: Jimny reduction gears |
Asps91 wrote: zukenutter wrote: suzkboy wrote: Stock sierra gears on 31s then 1L transfer for 31s I thought the 1l transfer didn't fit. There's two types, one has a 4WD light switch and is the same housing as 1.3L transfer. Flanges need to be swapped. |
|
| Author: | zukenutter [ Wed Jul 31, 2013 9:30 pm ] |
| Post subject: | Re: Jimny reduction gears |
luke1122 wrote: whats needed to fit a 1l transfer to a jimny? Same as fitting a 1.3 transfer http://www.auszookers.com/forum/viewtopic.php?f=5&t=22832 |
|
| Author: | luke1122 [ Thu Aug 01, 2013 12:47 pm ] |
| Post subject: | Re: Jimny reduction gears |
can the non switched 1l transfer be fitted? |
|
| Author: | atari4x4 [ Thu Aug 01, 2013 1:02 pm ] |
| Post subject: | Re: Jimny reduction gears |
not by the sounds of this: zukenutter wrote: Asps91 wrote: zukenutter wrote: suzkboy wrote: Stock sierra gears on 31s then 1L transfer for 31s I thought the 1l transfer didn't fit. There's two types, one has a 4WD light switch and is the same housing as 1.3L transfer. Flanges need to be swapped. |
|
| Author: | zukenutter [ Thu Aug 01, 2013 1:56 pm ] |
| Post subject: | Re: Jimny reduction gears |
I don't know, Fatzook would know for sure. If the dimensions and mount points are the same I would imagine it would but you'll never get the 4WD light in your instrument cluster to work. |
|
| Author: | zukenutter [ Thu Aug 01, 2013 1:58 pm ] |
| Post subject: | Re: Jimny reduction gears |
Also, the WT flanges may not fit the splines on a no switch transfer |
|
| Author: | sideways [ Thu Aug 01, 2013 2:12 pm ] |
| Post subject: | Re: Jimny reduction gears |
A non switched case will theoretically fit. The mounts are the same but you'l have to do something about the flanges as they can't be swapped to 1.3l ones. There's also no aftermarket gear options for them, unless you can dig up an up geared set from the early 80s. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|