Like the toyota kit?
| auszookers.com https://auszookers.com/forum/ |
|
| King pin setup. https://auszookers.com/forum/viewtopic.php?f=5&t=42206 |
Page 1 of 1 |
| Author: | 31zook [ Mon Jul 29, 2013 11:24 am ] |
| Post subject: | King pin setup. |
I was talking with someone recently and they recommended putting gasket goo (sealant) under the king pin to help keep the CV/Knuckle water tight. So upon rebuilding my front end I figured I'll give it a go. Now I have the dreaded Jimny death wobble, which I never had any experience with before. Before it was tight and direct on road. So I'm going to remove the goo. So my question is, does anyone else out there do this when they put their kingpins together? Wilso. |
|
| Author: | Matthew [ Mon Jul 29, 2013 11:35 am ] |
| Post subject: | Re: King pin setup. |
Can't comment on a jimny, but on a sierra, yes. The FSM states that it should be done. |
|
| Author: | Mike57 [ Mon Jul 29, 2013 1:21 pm ] |
| Post subject: | Re: King pin setup. |
Same for the Jimny. I used old fachioned avaiation form a gasket but any sealant should do. |
|
| Author: | mrw82 [ Mon Jul 29, 2013 1:36 pm ] |
| Post subject: | Re: King pin setup. |
Did you set the kingpin bearing preload correctly when installing the new bearings. Same shims with new bearings does not guarantee same amount of preload. |
|
| Author: | rockcrawlerdude [ Mon Jul 29, 2013 1:46 pm ] |
| Post subject: | Re: King pin setup. |
would it matter to much if i didnt put the sticky stiff under the king pin? |
|
| Author: | 31zook [ Mon Jul 29, 2013 2:41 pm ] |
| Post subject: | Re: King pin setup. |
I have never used any and never had a drama. Jimny's from the floor don't have enough preload in the king pins, so I don't run any shims at all. With it like this I have no wobble or shimmy. But as soon as I add a smear of goo it must take the tiniest bit of tension out of it and I get the shakes. The only shims I've seen avaliable for jimny's is ones that go under the king pin (sit flat on the bearing increasing weight, instead of lessening the weight and collecting the 4 bolts). |
|
| Author: | Jezza86 [ Mon Jul 29, 2013 3:02 pm ] |
| Post subject: | Re: King pin setup. |
i did this yesterday too! i ended up with .4mm under and .5 mm over the right hand wheel (new bearings, old cradle, because i didn't have a puller tool and couldn't get the cradle out) still have to add shims to the passenger side to get rid of the last bits of wobble. its currently got 0.2mm under and .2mm over, going to take the .2 from the top and put it on the bottom, test drive and if i have to put a 0.5mm on the top. im going to seal them with the gasket goo, but only once the wobbles are sorted. at the moment i cnt see that harm as its dry season... as standard the have a super thin bead of a silicone like goo on them. that's all im putting on to seal it. major differences in instructions i found was the amount of grease it takes to re grease the hub. bigjimny instructions recommend 100mlhttp://www.bigjimny.com/store/index.php?_a=product&product_id=8, some boris dude says 2-300ml. http://www.jimny.se/kingpinbearings.html |
|
| Author: | Jezza86 [ Mon Jul 29, 2013 3:10 pm ] |
| Post subject: | Re: King pin setup. |
http://www.bigjimny.com/images/document ... arings.pdf |
|
| Author: | monley [ Mon Jul 29, 2013 5:46 pm ] |
| Post subject: | Re: King pin setup. |
I always used a sealant on my king pins when ever I pulled the front end of my jim apart. Never made any difference |
|
| Author: | Jezza86 [ Mon Jul 29, 2013 6:48 pm ] |
| Post subject: | Re: King pin setup. |
still got heaps of water in there? mabie its to stop the grease escaping more than stopping the water (and mud) getting in there... |
|
| Author: | SierraDan [ Tue Jul 30, 2013 6:27 am ] |
| Post subject: | Re: King pin setup. |
The grease wont get out of the kingpins anytime soon. |
|
| Author: | joeblow [ Wed Jul 31, 2013 4:30 pm ] |
| Post subject: | Re: King pin setup. |
If there is any sign of water the top kingpin will dry out and corrode first. With my Jimny build I'm machining some solid tapered bearings that will be heat treated. These will eliminate the pitting associated with roller type kingpin bearings and allow for a higher preload setting. |
|
| Author: | SierraDan [ Wed Jul 31, 2013 6:08 pm ] |
| Post subject: | Re: King pin setup. |
Like the toyota kit?
|
|
| Author: | Jezza86 [ Wed Jul 31, 2013 9:40 pm ] |
| Post subject: | Re: King pin setup. |
i must admit i did sit on google for a half hour before i gave up on finding a 3030j made from titanium or something... is it something you might be making a batch of joe? |
|
| Author: | joeblow [ Thu Aug 01, 2013 2:07 pm ] |
| Post subject: | Re: King pin setup. |
Hopefully. The CNC lathe is just about finished having its tart up. Once that is done programs will be written. |
|
| Author: | sideways [ Thu Aug 01, 2013 2:16 pm ] |
| Post subject: | Re: King pin setup. |
joeblow wrote: With my Jimny build I'm machining some solid tapered bearings that will be heat treated. These will eliminate the pitting associated with roller type kingpin bearings and allow for a higher preload setting. They will become a JML product wont they? 
|
|
| Author: | Jezza86 [ Thu Aug 01, 2013 2:50 pm ] |
| Post subject: | Re: King pin setup. |
ill take 8. i can do all the corrugation testing. |
|
| Author: | SierraDan [ Thu Aug 01, 2013 3:16 pm ] |
| Post subject: | Re: King pin setup. |
joeblow wrote: Hopefully. The CNC lathe is just about finished having its tart up. Once that is done programs will be written. SierraDan wrote: Like the toyota kit?
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|