auszookers.com
https://auszookers.com/forum/

sierra lockrite issue
https://auszookers.com/forum/viewtopic.php?f=5&t=43182		 Page 1 of 1
Author:  Rbowl [ Sat Sep 28, 2013 9:15 pm ]
Post subject:  sierra lockrite issue
Hi guys.

Today I started installing the lockrite I've had sitting around for months. Pulling the standard diff apart was no problen, everything was going smoothly but the smoothness ended when I started installing the lockrite into the carrier. The thrust washers that are ment to be reused with the new side gears (the couplers supplied with the locker) are to small and do not fit. The couplers themselves do not fit into the carrier.

Have low range sent me the wrong locker... or is there somthing im not getting?
Has anyone had this problem before?
My diff is in pieces on the bench, I was hoping to have it all done today so its abit annoying.

Ill get some pics up soon.

Image

Image
Thanks.
Rhys.
Author:  Built4thrashing [ Sat Sep 28, 2013 9:43 pm ]
Post subject:  Re: sierra lockrite issue
Wrong couplers im guessing.


Do the couplers have the same spline count as the axles? 26spline?
Author:  Rbowl [ Sat Sep 28, 2013 11:04 pm ]
Post subject:  Re: sierra lockrite issue
I'll give them a count tomorrow, should have already done that. I'd say they are the wrong ones, problem is I bought them earlier this year... hopefully they will be willing yo swap them for the right ones..
Author:  Rbowl [ Sat Sep 28, 2013 11:08 pm ]
Post subject:  Re: sierra lockrite issue
Well I think I just counted 28 in the picture above. So yep, there the wrong ones.
Author:  303zuke [ Sat Sep 28, 2013 11:45 pm ]
Post subject:  Re: sierra lockrite issue
I count 27. Still wrong coupler.

What is the part number on the box?
Author:  Rbowl [ Sun Sep 29, 2013 8:40 am ]
Post subject:  Re: sierra lockrite issue
SAX-1530 is the number on the box, thats the right number isnt it. Just wrong locker inside.
Author:  Rbowl [ Sun Sep 29, 2013 8:41 am ]
Post subject:  Re: sierra lockrite issue
And your right, 27 spline.
Author:  Built4thrashing [ Sun Sep 29, 2013 8:46 am ]
Post subject:  Re: sierra lockrite issue
303zuke wrote:
I count 27. Still wrong coupler.




Same... I count 27.

Part number will help
Any numbers stamped on the locker itself
Author:  Rbowl [ Sun Sep 29, 2013 10:03 am ]
Post subject:  Re: sierra lockrite issue
Alright, one coupler is a 27 spline coupler with CAL H1 stamped on it, the other coupler supplied is a 26 spline coupler with CBY J1 stamped on it. There are very obvious differences between the 2(besides the spline count).. Why did I not see this yesterday? Now to wait for a reply from low range and hopefully get this sorted.

Thanks for the help guys!
Author:  ajsr [ Sun Sep 29, 2013 10:36 am ]
Post subject:  Re: sierra lockrite issue
I had the same problem with a locker from there
Author:  Rbowl [ Sun Sep 29, 2013 11:02 am ]
Post subject:  Re: sierra lockrite issue
Is that right? Usually there pretty good. Did they replace it with the right part?
Author:  sideways [ Sun Sep 29, 2013 3:25 pm ]
Post subject:  Re: sierra lockrite issue
ajsr wrote:
I had the same problem with a locker from there


This must be the 3rd or 4th time I've heard of this happening. :?
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/