who served you
| auszookers.com https://auszookers.com/forum/ |
|
| carbide burr for aluminium https://auszookers.com/forum/viewtopic.php?f=5&t=4368 |
Page 1 of 1 |
| Author: | Damo [ Fri Mar 20, 2009 11:55 am ] |
| Post subject: | carbide burr for aluminium |
Where should I go in Brissy to get one of these? |
|
| Author: | ball [ Fri Mar 20, 2009 12:27 pm ] |
| Post subject: | Re: carbide burr for aluminium |
What area are you in ? |
|
| Author: | Hybrid [ Fri Mar 20, 2009 12:59 pm ] |
| Post subject: | Re: carbide burr for aluminium |
Damo. If you go over to Evans Rd, Salisbury there's an industrial & Engineering supply place. They sell all the drill bits, taps and dies, bolts, burrs, measuring kit etc. that you can think of. I've tagged it below. Its on the corner of assembly and evans I think http://www.whereis.com/#session=MzU= |
|
| Author: | ball [ Fri Mar 20, 2009 3:58 pm ] |
| Post subject: | Re: carbide burr for aluminium |
Comag http://www.comag.com.au/ or Bolts and Industrial https://www.bolt.com.au/locations.php |
|
| Author: | Damo [ Fri Mar 20, 2009 4:22 pm ] |
| Post subject: | Re: carbide burr for aluminium |
Thanks guys, I ended up going to Blackwoods, only coz they are close and I didn't have time to drive too far. |
|
| Author: | royce [ Fri Mar 20, 2009 5:46 pm ] |
| Post subject: | Re: carbide burr for aluminium |
who served you
|
|
| Author: | Damo [ Fri Mar 20, 2009 6:12 pm ] |
| Post subject: | Re: carbide burr for aluminium |
royce wrote: who served you
You know exactly who 
|
|
| Author: | royce [ Fri Mar 20, 2009 8:41 pm ] |
| Post subject: | Re: carbide burr for aluminium |
no I dont, most of the people I knew all quit after me
|
|
| Author: | Damo [ Fri Mar 20, 2009 11:38 pm ] |
| Post subject: | Re: carbide burr for aluminium |
royce wrote: no I dont, most of the people I knew all quit after me
It was old mate with the dreds. I know now he is full of it coz he reckons you're a good bloke! 
|
|
| Author: | royce [ Sat Mar 21, 2009 2:00 am ] |
| Post subject: | Re: carbide burr for aluminium |
bwahahahahaha I bet there are plenty there would argue that point
|
|
| Author: | Rockhopper [ Sun Mar 22, 2009 10:05 am ] |
| Post subject: | Re: carbide burr for aluminium |
Just as a matter of interest, how long does it take to get served at Blackwoods in Brissy. Everytime I go to the one in Smithfield, I order what I need, then have to wait half an hour whilst whatever I order is picked from the warehouse. Last time I went in I ordered an assortment packet of roll pins. That took an hour cause all the warehouse staff had gone to lunch. |
|
| Author: | Damo [ Sun Mar 22, 2009 12:06 pm ] |
| Post subject: | Re: carbide burr for aluminium |
Rockhopper wrote: Just as a matter of interest, how long does it take to get served at Blackwoods in Brissy. Everytime I go to the one in Smithfield, I order what I need, then have to wait half an hour whilst whatever I order is picked from the warehouse. Last time I went in I ordered an assortment packet of roll pins. That took an hour cause all the warehouse staff had gone to lunch.
I was in & out in prolly 10 mins. Good timing maybe? |
|
| Author: | royce [ Sun Mar 22, 2009 10:56 pm ] |
| Post subject: | Re: carbide burr for aluminium |
Smithfield and Carole park are distribution centres and the orders have to run through the system like all the rest, your roll pins could well of been 3 stories up and your order had to work through the que for the dude on one of the big order pickers to get to it, they would rather you order ahead and pick it up or better yet piss off unless you are an account customer placing a decent order and happy to have it delivered 
|
|
| Author: | datso [ Mon Mar 30, 2009 6:31 pm ] |
| Post subject: | Re: carbide burr for aluminium |
One item I have never seen affordable over so many years are carbide burrs. absolutely crazy prices for some of them. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|