auszookers.com
https://auszookers.com/forum/

Jimny Sills.
https://auszookers.com/forum/viewtopic.php?f=5&t=43722		 Page 1 of 1
Author:  -QIK- [ Sun Nov 03, 2013 6:27 pm ]
Post subject:  Jimny Sills.
A few days ago I came across some pictures of a bolt on fabricated sill for the Jimny, it replaces the plastic.

I am ripping my hair out trying to find it again. These looked similar to the ones that go on a sierra.

Any ideas please?

Cheers,

Rob.
Author:  Birdman1985 [ Sun Nov 03, 2013 6:40 pm ]
Post subject:  Re: Jimny Sills.
Its a foreign website. He fabbed them up himself.

ahhh, i knew i had it in my bookmarks somewhere

http://forums.offipalsta.com/showthread ... ight=jimny
Author:  Joe [ Sun Nov 03, 2013 6:48 pm ]
Post subject:  Re: Jimny Sills.
atari4x4 wrote:
Jezza86 wrote:
:D Ball should make you some sliders
2 pairs of them.


you jokers seen these ones? http://www.fts4x4.com/en/products/?meth ... il&aid=666

Image

Image
Author:  Chop [ Sun Nov 03, 2013 6:53 pm ]
Post subject:  Re: Jimny Sills.
Thats what we need for the GV's Joe!
Author:  -QIK- [ Sun Nov 03, 2013 7:09 pm ]
Post subject:  Re: Jimny Sills.
Joe,

That's them!!!!!

Now to see if I can get some. :)
Author:  Skippy [ Thu Nov 07, 2013 6:46 am ]
Post subject:  Re: Jimny Sills.
Dis you happen to get a hold of the company QIK ? I sent off a email this morning
Author:  Jameszook [ Thu Nov 07, 2013 6:33 pm ]
Post subject:  Re: Jimny Sills.
Thos slider look madbitches
Author:  Skippy [ Fri Nov 08, 2013 10:28 pm ]
Post subject:  Re: Jimny Sills.
Dear Sir,

Thanks for your email.

The quotation as below for your reference.
JM2900  Jimny Heavy Duty Side Step (Steel Side Sill Guard)    USD345
Freight via EMS express to Australia                                          USD135
Total amount                                                                              USD480
Transit days: 4-6Just got an email back from fts4x4.
Author:  zukenutter [ Sat Nov 09, 2013 6:17 am ]
Post subject:  Re: Jimny Sills.
I'd like to see some mounting detail pics. Somebody buy a set so we can copy the mounts :twisted: :roll:
Author:  Skippy [ Sat Nov 09, 2013 6:54 am ]
Post subject:  Re: Jimny Sills.
how does the original mount?
Author:  zukenutter [ Sat Nov 09, 2013 7:48 am ]
Post subject:  Re: Jimny Sills.
Onto thin sheet metal tabs.
It looks like it tops into the sill ledge from the top, and I'm guessing underneath uses the pissy tabs.
Author:  Skippy [ Sat Nov 09, 2013 8:46 am ]
Post subject:  Re: Jimny Sills.
might take one off and have a look, was thinking i might take a plastic sill and the photos off the fts4x4 site into a metal fab shop and see if they could replicate them
Author:  zukenutter [ Sat Nov 09, 2013 9:00 am ]
Post subject:  Re: Jimny Sills.
I've been thinking of making something similar, There are also clips that go into the rounded vertical face of the sill behind the plastic which I'm thinking of utilising as well. I think that using face and tabs underneath, plus in from the top should make it strong enough.

Vertical face clip holes

Image

There are also extra unused tabs underneath, the plastic only utilises every second tab.
Author:  Jezza86 [ Sat Nov 09, 2013 9:09 am ]
Post subject:  Re: Jimny Sills.
zukenutter wrote:
I've been thinking of making something similar, There are also clips that go into the rounded vertical face of the sill behind the plastic which I'm thinking of utilising as well. I think that using face and tabs underneath, plus in from the top should make it strong enough.

Vertical face clip holes

Image

There are also extra unused tabs underneath, the plastic only utilises every second tab.

didnt you have the ODA sliders?
Author:  zukenutter [ Sat Nov 09, 2013 9:31 am ]
Post subject:  Re: Jimny Sills.
Yeah and they were great but I've done a deal with them to work up my own design :D
I'll rough up a side as best I can then hand it over to the steel guy.
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/