auszookers.com
https://auszookers.com/forum/

Shackle plates
https://auszookers.com/forum/viewtopic.php?f=5&t=4394		 Page 1 of 1
Author:  Damo [ Mon Mar 23, 2009 3:35 pm ]
Post subject:  Shackle plates
I got some of Bruce's bushes a couple of weeks ago and had a little time on the weekend to put some in.

Well, I found a couple of problems. Firstly, on the chassis mount end the old bushes were installed without any crush sleeve :roll: so you cant imagine the state of the bushes. On the shackle end things were just as bad, as the shackles must not have been quite tight enough and have been moving around, and the holes in the shackle plates are all flogged out. A few of the shackle pins are looking a bit ordinary as well.

Are these available new anywhere? I dont want longer shackles, just stock or close to. I was thinking I could make up the shackle plates myself but that still leaves the pins. I could just use bolts but was trying to keep things factory or close to.
Author:  Bruce [ Mon Mar 23, 2009 4:12 pm ]
Post subject:  Re: Shackle plates
http://www.suzistore.com.au/shopexd.asp?id=14
Author:  Bruce [ Mon Mar 23, 2009 4:14 pm ]
Post subject:  Re: Shackle plates
http://www.suzistore.com.au/shopexd.asp?id=765
Author:  Damo [ Mon Mar 23, 2009 4:21 pm ]
Post subject:  Re: Shackle plates
Cheers Bruce!
Author:  Scrawny [ Mon Mar 23, 2009 5:29 pm ]
Post subject:  Re: Shackle plates
On this note, just having a look under mine and found some of my bushes are a little loose in the spring eye. Is there discrepancies in the bush sizes Bruce? It doesn't really bother me, I'm just curious.
Author:  Bruce [ Mon Mar 23, 2009 7:03 pm ]
Post subject:  Re: Shackle plates
I had had a few people ask me this over a few years now. We made the moulds from new bushes so in theory the hole should be smaller as poly shrinks 1.5% meaning that the parts should be 1.5% smaller overall (Not an issue with such a small part). I have fitted bushes to Casper (and sold shit loads over the years) heaps of times and never had a worry at all with them. Unless the new parts we made the moulds from had quite larger holes from the start.

If this becomes a problem I could get another set of new bushes I guess, measure the I/D of the hole, throw the other moulds away, and make new ones.
Author:  tanshi [ Mon Mar 23, 2009 9:35 pm ]
Post subject:  Re: Shackle plates
I have used the bushes Bruce sells and have never had an issue beyond them being compatible with Pete's (fatzook) extended shackles. The bolt holes are made for im assuming 13mm or half inch bolts? The shackles have 12mm bolts, easy fixed i know but needed to be mentioned. also the space between the shackle plates is slightly too far apart for the bushes, ie .5 to 1mm gap, the shackles are welded in place. im not sure if this is a descrepancy in the bushes or the shackles tho
Author:  Damo [ Thu Mar 26, 2009 1:44 pm ]
Post subject:  Re: Shackle plates
I ordered those bits from Suzistore on Monday, and they arrived this morning. Not bad from WA.
Author:  Bruce [ Fri Mar 27, 2009 12:47 am ]
Post subject:  Re: Shackle plates
Yep I got my "S" for Casper's new grill today as well. :-)
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/