Ok thanks for that steve. Ad mnemonix, i dont specifically want it, i just found one at a good price thats all, ill have to check this chromoly one out cheers
| auszookers.com https://auszookers.com/forum/ |
|
| Hi steer without spoa https://auszookers.com/forum/viewtopic.php?f=5&t=44334 |
Page 1 of 1 |
| Author: | Abouwer123 [ Tue Dec 17, 2013 6:17 am ] |
| Post subject: | Hi steer without spoa |
Hey everyone, I was just wondering if you can run a high steer without doing a spoa conversion, I have a 2" spring, and 2 " shackles, the reason for this is I can get a new system second hand but brand new for a good price, and my tie rods are shot on mine, and the hi steer setup are all heavy duty. Thanks |
|
| Author: | Gwagensteve [ Tue Dec 17, 2013 7:07 am ] |
| Post subject: | Re: Hi steer without spoa |
I don't believe it's possible. It's something I have looked at a number of times, but there is just not enough room - the knuckle can travel up too far relative to the chassis with SPUA to permit clearance. Steve. |
|
| Author: | Abouwer123 [ Tue Dec 17, 2013 7:16 am ] |
| Post subject: | Re: Hi steer without spoa |
Ok thanks steve so even with the lift it wouldn't work. :/ Andre |
|
| Author: | Gwagensteve [ Tue Dec 17, 2013 7:36 am ] |
| Post subject: | Re: Hi steer without spoa |
Hi Andre, it doesn't have anything to do with the lift, it's all about where the axle ends up when the suspension is fully compressed. Whether you have shackles and lift springs or not, the axle can (should) still be able to reach the bumpstop, which is still in the factory position - so there's just no room - the tie rod will be about 1/2 way up the chassis rail. I reckon you'd need to space the bumpstops over three inches in order to try and run high steer, which, I think, is too much to have the car work well. I have looked at running it with cars running 2" of bumpstop spacing and it's not possible. It is advisable to flatten out your drag link angle though - your car will drive and steer much better if you do. A drop pitman arm is the best way of achieving this in your application. Steve. |
|
| Author: | alien [ Tue Dec 17, 2013 8:03 am ] |
| Post subject: | Re: Hi steer without spoa |
Could you run crossover steering instead? Or still no room? |
|
| Author: | mnemonix [ Tue Dec 17, 2013 8:12 am ] |
| Post subject: | Re: Hi steer without spoa |
Do you specifically want high steer, or do you just want heavy duty? Pete from Twins Stick Offroad makes a HD chromoly replacement sierra steering setup. It's a bloody good bit of gear. Look here: viewtopic.php?f=15&t=13126 |
|
| Author: | Abouwer123 [ Tue Dec 17, 2013 8:23 pm ] |
| Post subject: | Re: Hi steer without spoa |
Ok thanks for that steve. Ad mnemonix, i dont specifically want it, i just found one at a good price thats all, ill have to check this chromoly one out cheers
|
|
| Author: | Reubs [ Tue Dec 17, 2013 9:39 pm ] |
| Post subject: | Re: Hi steer without spoa |
mnemonix wrote: Pete from Twins Stick Offroad makes a HD chromoly replacement sierra steering setup. It's a bloody good bit of gear.Look here: http://auszookers.com/forum/viewtopic.php?f=15&t=13126 X2. Hizook runs those in Tough Tracks. Those arms still aren't bent pushing 33s with power steer and they also tend to collide with the odd rock as well! |
|
| Author: | SierraDan [ Wed Dec 18, 2013 6:09 am ] |
| Post subject: | Re: Hi steer without spoa |
6000series alloy is another good material. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|