I thought you were going to say "with fire"
Steve.
| auszookers.com https://auszookers.com/forum/ |
|
| whats the best way to clean up engine bay wiring? https://auszookers.com/forum/viewtopic.php?f=5&t=44684 |
Page 1 of 1 |
| Author: | Perram [ Tue Jan 14, 2014 10:48 am ] |
| Post subject: | whats the best way to clean up engine bay wiring? |
hey guys i have allot of 12v accessories and am looking to neaten up my fire hazzard... whats the best way to keep wiring neat? Jake |
|
| Author: | shep [ Tue Jan 14, 2014 12:25 pm ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
I find that the most effective method is to close the bonnet and pretend that every thing is awesome under it |
|
| Author: | Gwagensteve [ Tue Jan 14, 2014 12:46 pm ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
I thought you were going to say "with fire" Steve. |
|
| Author: | Jezza86 [ Tue Jan 14, 2014 1:45 pm ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
i used bus bar style power rails with screws tapped into them. did a positive and negative rail inside the cab. going to put a plastic cover over the positive eventually but at the moment its just live. got them from a boat shop. have a 100A fuse feeding them through a fat cable through the firewall. run a 400w amp, compressor, electronic break controller, and may one day run a fridge off it. |
|
| Author: | azzas15 [ Tue Jan 14, 2014 1:59 pm ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
Lots of black tape! Depending on who has had your car there may be old wiring from lights ect you could cut away |
|
| Author: | Blkfxx [ Tue Jan 14, 2014 2:48 pm ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
Split loom tubing and heatshrink! |
|
| Author: | mnemonix [ Tue Jan 14, 2014 3:49 pm ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
Give it to an auto electrician with a fist full of money. |
|
| Author: | 31zook [ Tue Jan 14, 2014 4:08 pm ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
I work at an auto elec shop, it would cost too much. Split tube and heat shrink 
|
|
| Author: | Skippy [ Tue Jan 14, 2014 4:46 pm ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
As others have said, wrinkle dick (split tube) and heat shrink. Plus this http://www.ebay.com.au/itm/FUSE-HOLDER-BOX-4-WAY-CARAVAN-4X4-DUAL-BATTERY-SYSTEM-12-VOLT-12V-NEW-/400607253473?pt=AU_Car_Parts_Accessories&hash=item5d460d93e1 Awesome idea, just one Power in and power out to everything and they are fused as well, i put one in the Jimny for UHF and my lightbar. 
|
|
| Author: | SuziBlu [ Wed Jan 15, 2014 1:34 pm ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
shep wrote: I find that the most effective method is to close the bonnet and pretend that every thing is awesome under it X2, out of sight out of mind, it works, woohoooo |
|
| Author: | royce [ Wed Jan 15, 2014 6:48 pm ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
Take some photos and outline what you want to do. Generally messy wiring is also not very efficient and hiding it doesnt help. |
|
| Author: | losfer [ Wed Jan 15, 2014 8:07 pm ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
This thread gets a genuine hardy laugh out of me ... |
|
| Author: | pezz [ Wed Jan 15, 2014 8:10 pm ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
i started with sorting out a neatish mounting bracket for all my bits, then ran all the wires i needed and cut to length then rip it all out and turned it into one big loom, taped, tubes soldered and then refitted i tried to follow factory wiring were posible and tucked it under things when possible too mine isnt the best job, but i think its far from the worst.. 
|
|
| Author: | shep [ Wed Jan 15, 2014 8:32 pm ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
I think it is important to never trim cable ties as that draws people's eyes away from the truly dodgy stuff. |
|
| Author: | Jezza86 [ Wed Jan 15, 2014 9:12 pm ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
shep wrote: I think it is important to never trim cable ties as that draws people's eyes away from the truly dodgy stuff. ill replace every cable tie before returning to QLD. sound advice shep thanks. what kind of which controll box is that under the bonnet? in the engine bay? seams lika a much better place to put one then where mine is I.E. full of water every time i go to use it |
|
| Author: | pezz [ Thu Jan 16, 2014 3:04 pm ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
Just the standard warn one that came with my winch |
|
| Author: | Perram [ Fri Jan 17, 2014 6:29 pm ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
I will get one tomorrow and try put it up Thanks for the help guys Probably wont go with yoyr suggestions shep, sorry good laugh thoughThanks jake |
|
| Author: | Zookrider [ Thu Feb 20, 2014 1:45 pm ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
if you are talking about aftermarket wiring, I ran a huge cable from the AUX BATT to a separate fusebox inside the cab up the passenger side firewall. I then made a board with solenoids (push on style for easy replacement) and even small sub fuse boxes for ON, ACC, LIGHTS. Then you can crimp on the connectors and plug them where they are supposed to go. Simple and easy to understand when you need to comeback later to troubleshoot or add something new. I only bother to shrink wrap joins,l the rest is tape, tape and more tape. Wide duct tape is great for less turns. |
|
| Author: | dank [ Sat Feb 22, 2014 7:08 am ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
The fuse box out of early vitaras are great for an accessory setup as they use the big squarish blade fuses that go up to 80odd amps. So you can run basically any accessory off them. I used one in my zook for running stuff like my big compressor and rear mounted thermo fans. Got it from a wrecker with a bunch of good battery cable and a handful of assorted fuses from a few vehicles for around 10 bucks. It has about five ports from memory. it'll allow you to remove everything off your battery to a better location like the passenger wheel arch or like above, inside the passenger firewall behind the dash. |
|
| Author: | Gwagensteve [ Mon Feb 24, 2014 5:39 am ] |
| Post subject: | Re: whats the best way to clean up engine bay wiring? |
Likewise EL/EF falcon. I grab the engine fuse box when I grab an alternator. Steve. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|