auszookers.com
https://auszookers.com/forum/

Jimny tough dog 60mm lift.
https://auszookers.com/forum/viewtopic.php?f=5&t=45053		 Page 1 of 1
Author:  Gromet [ Tue Feb 11, 2014 7:58 pm ]
Post subject:  Jimny tough dog 60mm lift.
Is it wrong for me to put the old standard front springs in the rear? Because the rear springs I got are more like 80mm lift and it looked odd and was to ridged.

Its made the ride smother and the height pretty close to the front. Is this something people do often?
Author:  jimny_timmy [ Tue Feb 11, 2014 8:50 pm ]
Post subject:  Re: Jimny tough dog 60mm lift.
Yeah it's been done before... I can't see any downside if it's sitting level... Measure from bottom of the rim to bottom of guard and check the difference in the front to back. If be interest to see how it sits. (Has to be level ground of course)
Author:  jimny_timmy [ Tue Feb 11, 2014 8:51 pm ]
Post subject:  Re: Jimny tough dog 60mm lift.
Also, are you sure the rear springs you were talking about... Are you sure they were for the rear? Fronts are a little longer ....
Author:  Gromet [ Tue Feb 11, 2014 8:56 pm ]
Post subject:  Re: Jimny tough dog 60mm lift.
:thefinger: Yeh I'm pretty sure I have them the right way... these are the measurements I got so far (from top of the rim to guard)

stock.
F/L 195mm F/R 195mm
R/L 192mm R/R 192mm

Put the springs and shocks in the first time. got it all sorts of wrong
Image
Author:  jimny_timmy [ Tue Feb 11, 2014 8:59 pm ]
Post subject:  Re: Jimny tough dog 60mm lift.
Is that pic from when you got it wrong? It "looks" to be pitching in the front a little there???
Author:  Gromet [ Tue Feb 11, 2014 9:04 pm ]
Post subject:  Re: Jimny tough dog 60mm lift.
I swiftly fixed that... now my rear left hand spring was the long one. I then had

Tough dog all around:
F/L 255mm F/R 255mm
R/L 270mm R/R 275mm

Now with stock front in the rear it is:
F/L 250mm F/R 255
R/L 255mm R/R 245 (But Ill need to let it settle tomorow)
Author:  Gromet [ Tue Feb 11, 2014 9:05 pm ]
Post subject:  Re: Jimny tough dog 60mm lift.
jimny_timmy wrote:
Is that pic from when you got it wrong? It "looks" to be pitching in the front a little there???


Yeh Fronts in the rear, Rear in the front haha
Author:  jimny_timmy [ Tue Feb 11, 2014 9:06 pm ]
Post subject:  Re: Jimny tough dog 60mm lift.
Sweet :) be interesting to see if it settles enough
Author:  jimny_timmy [ Tue Feb 11, 2014 9:06 pm ]
Post subject:  Re: Jimny tough dog 60mm lift.
Gromet wrote:
jimny_timmy wrote:
Is that pic from when you got it wrong? It "looks" to be pitching in the front a little there???


Yeh Fronts in the rear, Rear in the front haha

Happens to the best of us ;)
Author:  Gromet [ Tue Feb 11, 2014 9:12 pm ]
Post subject:  Re: Jimny tough dog 60mm lift.
jimny_timmy wrote:
Gromet wrote:
jimny_timmy wrote:
Is that pic from when you got it wrong? It "looks" to be pitching in the front a little there???


Yeh Fronts in the rear, Rear in the front haha

Happens to the best of us ;)


Yeh, well I Had a google search before I did it and it said I needed the long spring in the front.. but it must be diffrent with a winch bar
Author:  monley [ Wed Feb 12, 2014 6:13 am ]
Post subject:  Re: Jimny tough dog 60mm lift.
I had stock front springs in the rear of my old Jimny. They were all well and good until it was loaded up with camping gear where it handled liked Shit due to the soft spring rate, but that was a once in a blue moon id go camping. I ran 80mm springs in the front with 30mm spacers and it sat pretty close to level.
Author:  Gromet [ Wed Feb 12, 2014 5:31 pm ]
Post subject:  Re: Jimny tough dog 60mm lift.
Ok, So they settled in and sat at
F/L 265 F/R 255
R/L 255 R/R 245
So I simply put a 8mm hub spacer between the rubber boot and cradle. (was all I had) bit dodgy haha.

But it all sits nice and level pretty much 255mm all around.

Image

Image
Author:  Gromet [ Wed Feb 12, 2014 5:36 pm ]
Post subject:  Re: Jimny tough dog 60mm lift.
Image
Author:  jimny_timmy [ Wed Feb 12, 2014 6:17 pm ]
Post subject:  Re: Jimny tough dog 60mm lift.
Looks a bit better :)

I would have thought the fronts would have handled a little more weight due to the weight of the motor etc up front... Although I spose they aren't a lifted spring either.

P.S. Monley... What happened to you on facey? You gone AWOL?
Author:  Jezza86 [ Wed Feb 12, 2014 6:49 pm ]
Post subject:  Re: Jimny tough dog 60mm lift.
andy is in hiding so he doesnt get fired from looking at his phone all day instead of pretending to weld
Author:  Gromet [ Wed Feb 12, 2014 6:52 pm ]
Post subject:  Re: Jimny tough dog 60mm lift.
Yeh I was surprised it was as smooth as it was with the front sprngs in the rear... but a steal bar would be smoother then the Tough Dog "springs".
Author:  monley [ Wed Feb 12, 2014 7:36 pm ]
Post subject:  Re: Jimny tough dog 60mm lift.
Jezza86 wrote:
andy is in hiding so he doesnt get fired from looking at his phone all day instead of pretending to weld

^^^What he said :lol:

jimny_timmy wrote:

P.S. Monley... What happened to you on facey? You gone AWOL?
Author:  jimny_timmy [ Wed Feb 12, 2014 7:37 pm ]
Post subject:  Re: Jimny tough dog 60mm lift.
:rofl:
Author:  obansam [ Tue Apr 14, 2015 6:06 am ]
Post subject:  Re: Jimny tough dog 60mm lift.
Gromet wrote:
Ok, So they settled in and sat at
F/L 265 F/R 255
R/L 255 R/R 245
So I simply put a 8mm hub spacer between the rubber boot and cradle. (was all I had) bit dodgy haha.

But it all sits nice and level pretty much 255mm all around.

Image

Image



Hi Grommet,

Do you still have your stock springs in the rear? How's the handling, as I'm considering doing the same. Based on what Monley says it wasn't so good when loaded up?

Cheers
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/