| auszookers.com https://auszookers.com/forum/ |
|
| g16b turbo on a g13bb https://auszookers.com/forum/viewtopic.php?f=5&t=45154 |
Page 1 of 1 |
| Author: | SPEEDY [ Wed Feb 19, 2014 8:26 pm ] |
| Post subject: | g16b turbo on a g13bb |
I want to turbo my g13bb jimny and I found a new turbo set up for a g16b, would there be any problems putting it on my engine or would it be bad? |
|
| Author: | mnemonix [ Wed Feb 19, 2014 8:32 pm ] |
| Post subject: | Re: g16b turbo on a g13bb |
If this is the question you need to ask, you're not up to the task of an aftermarket turbo conversion. |
|
| Author: | SPEEDY [ Thu Feb 20, 2014 5:17 am ] |
| Post subject: | Re: g16b turbo on a g13bb |
I'm not installing it, just buying the kit cheap, I just don't want to buy a kit that won't work. |
|
| Author: | droverdave [ Thu Feb 20, 2014 8:09 am ] |
| Post subject: | Re: g16b turbo on a g13bb |
What do you mean kit? The easiest and probably most important part is does a g16b exhaust manifold match a g13bb. If it fits on, then you are one step towards it "fitting". It's a small step though. |
|
| Author: | SPEEDY [ Thu Feb 20, 2014 8:31 am ] |
| Post subject: | Re: g16b turbo on a g13bb |
Yes, that's the sort of thing I need to know, I haven't seen it yet, but if the exhaust manifolds match and the blocks are similar enough so all the plumbing will match up then I will probably get it If all I need is an after market ecu or a remapping then its worthwhile. But if too much stuff wont line up then its just an expensive turbo with a manifold and plumbing that will be of no use to me. |
|
| Author: | Gwagensteve [ Thu Feb 20, 2014 8:36 am ] |
| Post subject: | Re: g16b turbo on a g13bb |
As has been said, manifold- yes. Plumbing- not necessarily. There's front and side facing g16b inlet manifolds, but only front facing g13bb. Swapping inlet manifolds will likely mean sensor/computer changes. All up it's going to be an expensive install in any case. Steve. |
|
| Author: | SPEEDY [ Thu Feb 20, 2014 10:10 am ] |
| Post subject: | Re: g16b turbo on a g13bb |
Gwagensteve wrote: As has been said, manifold- yes. Plumbing- not necessarily. There's front and side facing g16b inlet manifolds, but only front facing g13bb. Swapping inlet manifolds will likely mean sensor/computer changes. All up it's going to be an expensive install in any case. Steve. Thanks, that's about all I needed to know, if it would be feasible and cost effective. From the sounds of it, it won't be. |
|
| Author: | Gwagensteve [ Thu Feb 20, 2014 10:52 am ] |
| Post subject: | Re: g16b turbo on a g13bb |
Plumbing and manifolds are cheap compared to the compressor and tuning, so I don't see the position of the throttle body being a big issue really. Steve |
|
| Author: | shep [ Thu Feb 20, 2014 11:04 am ] |
| Post subject: | Re: g16b turbo on a g13bb |
This business might do a kit for a g series motor. http://www.bulletcars.com/superchargers/suzuki/ |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|