hey guys
whats this diff center out of???
its 3.9 ratio
26 spline
but its different to my nt centers.
it fits in my nt housing and wt housings.
can I use it in my wt housings???
cheers andrew
| auszookers.com https://auszookers.com/forum/ |
|
| whats this diff??? https://auszookers.com/forum/viewtopic.php?f=5&t=4522 |
Page 1 of 1 |
| Author: | ajsr [ Mon Apr 06, 2009 11:11 pm ] |
| Post subject: | whats this diff??? |
hey guys whats this diff center out of??? its 3.9 ratio 26 spline but its different to my nt centers. it fits in my nt housing and wt housings. can I use it in my wt housings??? cheers andrew
|
|
| Author: | royce [ Mon Apr 06, 2009 11:16 pm ] |
| Post subject: | Re: whats this diff??? |
I am guessing coily rear |
|
| Author: | ajsr [ Mon Apr 06, 2009 11:20 pm ] |
| Post subject: | Re: whats this diff??? |
can I use it in my wt housing royce??? |
|
| Author: | royce [ Mon Apr 06, 2009 11:23 pm ] |
| Post subject: | Re: whats this diff??? |
NFI, I assume so, if it botls in and the axles slide in probably does ARB list a different locker for coilys? |
|
| Author: | ajsr [ Mon Apr 06, 2009 11:24 pm ] |
| Post subject: | Re: whats this diff??? |
Joe will know |
|
| Author: | Saam [ Mon Apr 06, 2009 11:40 pm ] |
| Post subject: | Re: whats this diff??? |
coily for sure you could get an arb for them and the splines are the same the axles where just longer. a giveaway will be the threaded flange and those two bolts on the top where for the vibration stopped thing 
here is a picture of one ... lol |
|
| Author: | ajsr [ Tue Apr 07, 2009 12:18 am ] |
| Post subject: | Re: whats this diff??? |
Saam wrote: coily for sure you could get an arb for them and the splines are the same the axles where just longer.
a giveaway will be the threaded flange and those two bolts on the top where for the vibration stopped thing here is a picture of one ... lol yep I see the bit your talking about lol |
|
| Author: | joeblow [ Tue Apr 07, 2009 12:20 am ] |
| Post subject: | Re: whats this diff??? |
ajsr wrote: Joe will know
yes......coily, just make sure to count teeth. |
|
| Author: | ajsr [ Tue Apr 07, 2009 12:26 am ] |
| Post subject: | Re: whats this diff??? |
joeblow wrote: ajsr wrote: Joe will know yes......coily, just make sure to count teeth. 43crown and 11 pinion teeth 3.9:1 same as my nt ones and same as the nt front air locker. is the flange the same bolt pattern as the nt tailshafts joe? and will the center fit my rear housing ???? |
|
| Author: | Zook_Fan [ Tue Apr 07, 2009 12:38 am ] |
| Post subject: | Re: whats this diff??? |
y not run it in the front with chromo cv's? |
|
| Author: | Mike [ Tue Apr 07, 2009 12:40 am ] |
| Post subject: | Re: whats this diff??? |
because he has a front air locker already |
|
| Author: | Zook_Fan [ Tue Apr 07, 2009 12:43 am ] |
| Post subject: | Re: whats this diff??? |
well that would make sense then |
|
| Author: | ajsr [ Tue Apr 07, 2009 3:33 am ] |
| Post subject: | Re: whats this diff??? |
thanks for the help guys wide track flanges are different to narrow right?? whats the easiest way to make compatible between the two??swap flanges or yokes? cheers andrew |
|
| Author: | Mike [ Tue Apr 07, 2009 3:35 am ] |
| Post subject: | Re: whats this diff??? |
the easiest thing to do is use half the NT and Half the WT shaft |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|