Bench
http://www.gumtree.com.au/s-ad/acacia-r ... 1049623033
Hammer
http://www.blackwoods.com.au/search/ham ... ?c=Product
Here you go buddy
| auszookers.com https://auszookers.com/forum/ |
|
| DIY uni joint? https://auszookers.com/forum/viewtopic.php?f=5&t=46791 |
Page 1 of 1 |
| Author: | suzukikid [ Sun Jun 29, 2014 11:08 am ] |
| Post subject: | DIY uni joint? |
Hey all is there a DIY uni joint thread? Searched but nothing shows up..... Gotta do a couple |
|
| Author: | Blkfxx [ Sun Jun 29, 2014 11:46 am ] |
| Post subject: | Re: DIY uni joint? |
Couldn't find one on here, but... http://www.billjohn.com/articles/drivet ... ujoint.htm |
|
| Author: | atari4x4 [ Sun Jun 29, 2014 12:02 pm ] |
| Post subject: | Re: DIY uni joint? |
it's pretty straight forward, i use this technique make sure you mark driveshaft so it goes back together the same way. mark the slip joint & either end of the driveshaft & the flanges/yokes. this is the other way, but be careful not to butcher the shaft with the grinder http://www.auszookers.com/forum/viewtop ... it=uni%27s |
|
| Author: | suzukikid [ Sun Jun 29, 2014 1:17 pm ] |
| Post subject: | Re: DIY uni joint? |
Righto thanks for that! Ill give the one in the video a go! |
|
| Author: | 31zook [ Sun Jun 29, 2014 2:10 pm ] |
| Post subject: | Re: DIY uni joint? |
^if you click on the AZ link it tells you that 2 or more sierra owners wrecked their shafts doing it the way in the video |
|
| Author: | atari4x4 [ Sun Jun 29, 2014 2:28 pm ] |
| Post subject: | Re: DIY uni joint? |
i guess sierra's being a good few years old & most having done real offroad work unlike most vits they're probably well & truly seized. i found that once in the vice with a little bit of load on them a decent knock on the ears usually is enough to shock the cap free... don't keep winding if it feels like it's binding up. |
|
| Author: | suzukikid [ Sun Jun 29, 2014 4:03 pm ] |
| Post subject: | Re: DIY uni joint? |
I gave it a crack in my vice but no good.... I didn't wanna wack it too hard.... My mate has a press I will use.... |
|
| Author: | shep [ Sun Jun 29, 2014 5:01 pm ] |
| Post subject: | Re: DIY uni joint? |
I did a how to thread a few years ago. Piss easy technique, just need a solid bench and a good copper hammer. |
|
| Author: | suzukikid [ Mon Jun 30, 2014 7:01 am ] |
| Post subject: | Re: DIY uni joint? |
Have you got a link to it? Cheers |
|
| Author: | 31zook [ Mon Jun 30, 2014 9:41 am ] |
| Post subject: | Re: DIY uni joint? |
Bench http://www.gumtree.com.au/s-ad/acacia-r ... 1049623033 Hammer http://www.blackwoods.com.au/search/ham ... ?c=Product Here you go buddy
|
|
| Author: | SierraDan [ Mon Jun 30, 2014 1:06 pm ] |
| Post subject: | Re: DIY uni joint? |
^ 
|
|
| Author: | atari4x4 [ Mon Jun 30, 2014 1:23 pm ] |
| Post subject: | Re: DIY uni joint? |
| viewtopic.php?f=5&t=24729&hilit=uni
|
|
| Author: | suzukikid [ Mon Jun 30, 2014 9:23 pm ] |
| Post subject: | Re: DIY uni joint? |
31zook wrote: Bench http://www.gumtree.com.au/s-ad/acacia-r ... 1049623033 Hammer http://www.blackwoods.com.au/search/ham ... ?c=Product Here you go buddy Hahahaha I had a good laugh! I really needed a bigger vice... Got the bench and being a chippy I got plenty of hammers! Haha cheers anyway bloke! |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|