monley wrote:
I don't run a o2 sensor in my g16b. I have the CEL hooked up and it doesn't come on
Don't worry it'll pop up once you go for a descent drive
| auszookers.com https://auszookers.com/forum/ |
|
| Getting g16b tuned idling high https://auszookers.com/forum/viewtopic.php?f=5&t=47346 |
Page 1 of 1 |
| Author: | Sutho [ Sun Aug 10, 2014 10:28 am ] |
| Post subject: | Getting g16b tuned idling high |
Hey guys! Just finished my G16b conversion in my Zook It's idling around 1500rpm at a constant level Yes I've searched this Is there anyone around brisbane that tunes these so I can lower the rpms? |
|
| Author: | droverdave [ Sun Aug 10, 2014 10:57 am ] |
| Post subject: | Re: Getting g16b tuned idling high |
You don't need a tune, you need to find the idle screw and adjust it, or find the leak that is letting air into the intake manifold. |
|
| Author: | Sutho [ Sun Aug 10, 2014 11:02 am ] |
| Post subject: | Re: Getting g16b tuned idling high |
Tried that screw mate And there's no leaks, look for that also |
|
| Author: | droverdave [ Sun Aug 10, 2014 11:21 am ] |
| Post subject: | Re: Getting g16b tuned idling high |
Hmm well you cant tune the ecu or anything. You can make sure the intake air control valve is working correctly? Sometimes they get blocked up. Have you bled the coolant system properly? |
|
| Author: | Sutho [ Sun Aug 10, 2014 11:28 am ] |
| Post subject: | Re: Getting g16b tuned idling high |
Oh ok Yeah I have I pulled it apart yesterday and cleaned it up, I may have to do that again, I pulled the hose off the outlet side of it and heaps of water smashed out of it so it can't be blocked |
|
| Author: | Sutho [ Sun Aug 10, 2014 11:41 am ] |
| Post subject: | Re: Getting g16b tuned idling high |
It's only running extractors ATM with no 02 sensor in them yet, would that matter? |
|
| Author: | watermouse [ Sun Aug 10, 2014 1:05 pm ] |
| Post subject: | Re: Getting g16b tuned idling high |
Sutho wrote: It's only running extractors ATM with no 02 sensor in them yet, would that matter? I would say that certainly matters. The ECU is looking for the sensor temp to come up first. If you are not using the donor cars dash then you might not be seeing it throw a code for the o2 sensor. It is a vital part of the EFI and emissions system. |
|
| Author: | Sutho [ Sun Aug 10, 2014 2:17 pm ] |
| Post subject: | Re: Getting g16b tuned idling high |
No worries mate I am getting a exhuast system Wednesday! And I will see how it goes But any more suggestions will be most welcome |
|
| Author: | monley [ Mon Aug 11, 2014 7:34 pm ] |
| Post subject: | Re: Getting g16b tuned idling high |
I don't run a o2 sensor in my g16b. I have the CEL hooked up and it doesn't come on - it idles at 1000rpm. Is your throttle cable adjusted correctly? |
|
| Author: | JrZook [ Mon Aug 11, 2014 7:58 pm ] |
| Post subject: | Re: Getting g16b tuned idling high |
monley wrote: I don't run a o2 sensor in my g16b. I have the CEL hooked up and it doesn't come on Don't worry it'll pop up once you go for a descent drive
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|