| auszookers.com https://auszookers.com/forum/ |
|
| Sierra 1.0 swb body mounts https://auszookers.com/forum/viewtopic.php?f=5&t=49919 |
Page 1 of 1 |
| Author: | Marcos [ Fri Apr 24, 2015 6:48 pm ] |
| Post subject: | Sierra 1.0 swb body mounts |
Hey guys, wondering if anyone can shine some light on this... Purchased a BYE body lift kit specifically for the 1litre, it's come with 4 female bolts and 6 male bolts. From what I can gather there are 6 fixed studs in the middle of the body not 4. So I'm thinking they may have screwed up when packing the kit, unless the early 1.0l sj's are different? This is what I can make out from previous threads, obviously I can't tell for sure until I lift the body and have a look. Would suck to get that far then have to put everything back on with no lift! What's your thoughts should I go for it?? |
|
| Author: | Marcos [ Fri Apr 24, 2015 6:53 pm ] |
| Post subject: | Re: Sierra 1.0 swb body mounts |
Even in the instructions it lists 6 female and 4 male! Ahhh doesn't look promising |
|
| Author: | Scrawny [ Fri Apr 24, 2015 6:57 pm ] |
| Post subject: | Re: Sierra 1.0 swb body mounts |
Sounds like a minor mix up. Get in touch with him and he'll sort you out |
|
| Author: | Bruce [ Fri Apr 24, 2015 6:58 pm ] |
| Post subject: | Re: Sierra 1.0 swb body mounts |
Well contact Greg (Just_Cruizin) and chat to him. He's a great guy and if there was an error he will sort it out. |
|
| Author: | Marcos [ Fri Apr 24, 2015 8:30 pm ] |
| Post subject: | Re: Sierra 1.0 swb body mounts |
It's strange, not only is the quantity of bolts different, the blocks match up, iv got 6 sleeved ones for the male and 4 unsleeved for the female. I'm wondering if it is correct for the 1.0l? I left the car at work il have to take a look in the morning, fingers crossed it's all good and I can get it done! I sent Greg an email anyway so il see what he reckons. |
|
| Author: | Blkfxx [ Fri Apr 24, 2015 8:58 pm ] |
| Post subject: | Re: Sierra 1.0 swb body mounts |
Gwagensteve wrote: 1.0 only requires 4 captive bolts. The inside two near the rear seat bolts are normal bolts.
Steve. |
|
| Author: | Marcos [ Fri Apr 24, 2015 10:22 pm ] |
| Post subject: | Re: Sierra 1.0 swb body mounts |
Cheers Steve u legend! Nice one mate, looking forward to getting stuck in tomorrow morning now! |
|
| Author: | Marko_SJ [ Fri Apr 24, 2015 10:37 pm ] |
| Post subject: | Re: Sierra 1.0 swb body mounts |
Marcos wrote: Cheers Steve u legend! Nice one mate, looking forward to getting stuck in tomorrow morning now! Steve's obviously pumped out so much good info over the years that he doesn't even have to reply to a thread to help people and get called a legend. 
|
|
| Author: | just_cruizin [ Sat Apr 25, 2015 7:17 pm ] |
| Post subject: | Re: Sierra 1.0 swb body mounts |
Yep, the instructions are written around 1.3lt Sierra's, the 1.0lts are different. Both in the mounts beside the tunnel being loose bolts but also the the rubbers being thinner. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|