| auszookers.com https://auszookers.com/forum/ |
|
| Dif spacer for 92 Vitara https://auszookers.com/forum/viewtopic.php?f=5&t=50484 |
Page 1 of 1 |
| Author: | Bush Pig [ Mon Jul 06, 2015 11:20 pm ] |
| Post subject: | Dif spacer for 92 Vitara |
Hi all, I installed a 2" suspension lift and a 2" body lift on my '92 SWB Vitara. What is the right size diff spacer i would need and where can i buy it ? Cheers |
|
| Author: | Gwagensteve [ Tue Jul 07, 2015 5:49 am ] |
| Post subject: | Re: Dif spacer for 92 Vitara |
It's unlikely you need one at all. |
|
| Author: | Bush Pig [ Tue Jul 07, 2015 7:16 am ] |
| Post subject: | Re: Dif spacer for 92 Vitara |
Hi Gwagensteve, How can determine that ? To me it looks like there is a lot of "extra" space but did not check before so have no reference. Cheers |
|
| Author: | ozzycouch [ Tue Jul 07, 2015 7:48 am ] |
| Post subject: | Re: Dif spacer for 92 Vitara |
If you mean drive shaft spacer, around 25mm. |
|
| Author: | jdk81 [ Tue Jul 07, 2015 8:45 am ] |
| Post subject: | Re: Dif spacer for 92 Vitara |
Body lift wont affect it, its just extra lift. Did your suspension lift change any of the rear links? If not, you wont need one as you are still within the design travel. If you add a spacer you may bind at full compression. There is a lot of spline travel on a vit xfer and driveshaft. Ill measure one if you want. |
|
| Author: | Bush Pig [ Tue Jul 07, 2015 9:15 am ] |
| Post subject: | Re: Dif spacer for 92 Vitara |
Yes Ozziecouch/Jdk81, was talking about the rear driveshaft. Not sure how to check if i need one. Would be nice to know how much i have to work with. Dont want break anything. Any advice ? Still new at this. Cheers |
|
| Author: | Gwagensteve [ Tue Jul 07, 2015 9:55 am ] |
| Post subject: | Re: Dif spacer for 92 Vitara |
You don't need one with a 2" lift. Steve. |
|
| Author: | Bush Pig [ Tue Jul 07, 2015 9:57 am ] |
| Post subject: | Re: Dif spacer for 92 Vitara |
Thanx Steve. |
|
| Author: | christover1 [ Wed Jul 08, 2015 7:51 am ] |
| Post subject: | Re: Dif spacer for 92 Vitara |
I settled on a 12mm tail shaft spacer for my 93 LWB with 2" lift onto OME 40mm springs, mainly to take out the looseness in worn splines of tail shaft. I cycled the suspension and decided any more would risk it punching the transfer case. Did not look like it could fall out, either. Do your measurings and decide. Is unlikely you will need a spacer, but don't go too big. Got mine from Bits4Vits in UK but I think there is many US suppliers. 
|
|
| Author: | Bush Pig [ Wed Jul 08, 2015 11:04 am ] |
| Post subject: | Re: Dif spacer for 92 Vitara |
Hi Christover1, Thank you very much for your advice. I am all new to this. How do i go about measuring it ? Cheers |
|
| Author: | Gwagensteve [ Wed Jul 08, 2015 11:10 am ] |
| Post subject: | Re: Dif spacer for 92 Vitara |
You don't need one at 2" of lift. There's nothing to measure. |
|
| Author: | Bush Pig [ Wed Jul 08, 2015 11:24 am ] |
| Post subject: | Re: Dif spacer for 92 Vitara |
Ok, case closed. I'll take your word for it Strve. Thanx |
|
| Author: | christover1 [ Wed Jul 08, 2015 11:58 am ] |
| Post subject: | Re: Dif spacer for 92 Vitara |
As said by all, not needed on 2 "or less. But if you want to measure something, just make sure it can't go in too deep, or fall out. |
|
| Author: | got_bar_work [ Thu Jul 09, 2015 5:47 am ] |
| Post subject: | Re: Dif spacer for 92 Vitara |
I would say u shouldn't need one at all unless u have a ball joint spacer. The balljoint is the limiting strap as such. If u add 50mm extra down travel that would be when u need the spacer . Or when u add longer links or non ball joint upper like calmini etc |
|
| Author: | ozzycouch [ Fri Jul 10, 2015 7:01 am ] |
| Post subject: | Re: Dif spacer for 92 Vitara |
Checked mine just now, under two inch lift (iron man), no ball joint spacer, 18mm drive shaft spacer. Been running the same setup for four years. |
|
| Author: | Gwagensteve [ Fri Jul 10, 2015 7:30 am ] |
| Post subject: | Re: Dif spacer for 92 Vitara |
18mm is a lot. I'd be taking the springs out, fully compressing the rear end, and checking that you still have at least 10-15mm of plunge on the slip yoke. There should be no need for a spacer, it creates more risk of bottoming the slip yoke, which can be catastrophic. |
|
| Author: | ozzycouch [ Fri Jul 10, 2015 9:36 am ] |
| Post subject: | Re: Dif spacer for 92 Vitara |
At the start of this post is a picture of how far it was sticking out of the gear box. http://www.auszookers.com/forum/viewtopic.php?f=37&t=32506 I'll measure it up if the suspension ever gets changed again, but 3 years of daily driving, wheeling, jumps up the beach, even a round of tough tracks, no catastrophic failures yet. |
|
| Author: | Gjrogers [ Thu Mar 24, 2016 11:45 am ] |
| Post subject: | Re: Dif spacer for 92 Vitara |
christover1 wrote: I settled on a 12mm tail shaft spacer for my 93 LWB with 2" lift onto OME 40mm springs, mainly to take out the looseness in worn splines of tail shaft. I cycled the suspension and decided any more would risk it punching the transfer case. Did not look like it could fall out, either. Do your measurings and decide. Is unlikely you will need a spacer, but don't go too big. Got mine from Bits4Vits in UK but I think there is many US suppliers. with the 12mm spacer how much of your slip yoke is sticking out of the box? |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|