Yep, you've popped something. Most likely a diode or transistor. I did something similar with the trolley tug by wiring the check engine light incorrectly, from memory.
| auszookers.com https://auszookers.com/forum/ |
|
| Have i Killed my ECU? https://auszookers.com/forum/viewtopic.php?f=5&t=50581 |
Page 1 of 1 |
| Author: | d.wamsley [ Sun Jul 19, 2015 5:57 pm ] |
| Post subject: | Have i Killed my ECU? |
Short story. g16a efi auto conversion. Had spark. added wiring for fuel pump. main relay and fuel pump relay only operating on crank. revised wiring. possibly had a retard moment and added power to wrong wiring. Now no spark no relays switching. blue relay control wire between ecu and main relay is showing 5 ish v but jumping to 12v in the on position. is this normal? does the control wire operate the relay by going to earth or 12v. any input appreciated Darren |
|
| Author: | Rhinoman [ Mon Jul 20, 2015 5:41 am ] |
| Post subject: | Re: Have i Killed my ECU? |
The main relay is switched to earth by the ECU. |
|
| Author: | d.wamsley [ Mon Jul 20, 2015 6:50 am ] |
| Post subject: | Re: Have i Killed my ECU? |
Thank you for the reply. The fact that I have 12v coming from the ecu wire, I must have a problem somewhere. |
|
| Author: | Rhinoman [ Mon Jul 20, 2015 6:56 am ] |
| Post subject: | Re: Have i Killed my ECU? |
You may still have it wired up wrong. You should have 12V to the relay so you'll see 12V on the ECU side if its not properly grounded. The main relay just goes through a diode on the ECU, if you put power on that line then you'll probably burn out the track, its a safety mechanism to stop the ECU being stuck on by the diode blowing up.. |
|
| Author: | d.wamsley [ Mon Jul 20, 2015 8:46 am ] |
| Post subject: | Re: Have i Killed my ECU? |
Thanks. I will check it out. I had the cover off yesterday and could not see any obvious damage, but it did have a smoky smell. Thanks for the info. Appreciate it., |
|
| Author: | Gwagensteve [ Mon Jul 20, 2015 9:06 am ] |
| Post subject: | Re: Have i Killed my ECU? |
Yep, you've popped something. Most likely a diode or transistor. I did something similar with the trolley tug by wiring the check engine light incorrectly, from memory.
|
|
| Author: | d.wamsley [ Mon Jul 20, 2015 9:27 am ] |
| Post subject: | Re: Have i Killed my ECU? |
Ouch! That's no good. I suppose I'm on the look out for a ecu now. The joys of modding. |
|
| Author: | Gwagensteve [ Mon Jul 20, 2015 9:43 am ] |
| Post subject: | Re: Have i Killed my ECU? |
ECU's are repairable - they're very ruggedly engineered and will normally blow something replaceable like a diode or power transistor without causing permanent damage to the rest of the computer. I'd look into repair. If you can smell a burnt/smoky smell you should be able to spot where the failure occurred. Steve. |
|
| Author: | d.wamsley [ Mon Jul 20, 2015 9:52 am ] |
| Post subject: | Re: Have i Killed my ECU? |
Thanks. I will look into that. That sounds like a good option. |
|
| Author: | d.wamsley [ Mon Jul 20, 2015 9:31 pm ] |
| Post subject: | Re: Have i Killed my ECU? |
I opened up my ecu and discovered a burnt out trace which is for the main relay control. I have had a go at repairing it with a conductive pen. Fingers crossed it passes continuity when it dries. If that fails I will solder it. Thanks for the help. |
|
| Author: | Rhinoman [ Mon Jul 20, 2015 9:35 pm ] |
| Post subject: | Re: Have i Killed my ECU? |
I would recommend that you use a 30awg wire link to bypass the trace - don't go to a higher gauge as it won't be as safe. |
|
| Author: | d.wamsley [ Tue Jul 21, 2015 12:51 pm ] |
| Post subject: | Re: Have i Killed my ECU? |
Circuit Pen did not work. Soldered in a bridge all works good now. Thank you for your help 
|
|
| Author: | dank [ Tue Jul 21, 2015 1:22 pm ] |
| Post subject: | Re: Have i Killed my ECU? |
this is forum tech help at its best! almost makes me emotional after seeing all the crap on FB pages these days! Takes me back to the good old days of 2008. LOL |
|
| Author: | d.wamsley [ Tue Jul 21, 2015 9:04 pm ] |
| Post subject: | Re: Have i Killed my ECU? |
 My repair job |
|
| Author: | d.wamsley [ Tue Jul 21, 2015 9:05 pm ] |
| Post subject: | Re: Have i Killed my ECU? |
The burnt trace 
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|