shep wrote:
Bugger. Ball was right.
Cheers
Cheers
| auszookers.com https://auszookers.com/forum/ |
|
| Joe blow rear disk and full float kits abs jimny https://auszookers.com/forum/viewtopic.php?f=5&t=52450 |
Page 1 of 1 |
| Author: | shep [ Tue May 10, 2016 8:35 am ] |
| Post subject: | Joe blow rear disk and full float kits abs jimny |
Does anyone have any pics of the assembled kits. About to fit them to a spare housing and can't see how it all goes together. |
|
| Author: | shep [ Sat May 14, 2016 11:28 am ] |
| Post subject: | Re: Joe blow rear disk and full float kits abs jimny |
Slowly getting there with zero info. So far have had to mod every part including the diff housing. Does the original wheelbearing get used or is the axle now supported by the diff centre and the centre bearing in the stub axle |
|
| Author: | Gwagensteve [ Sat May 14, 2016 4:12 pm ] |
| Post subject: | Re: Joe blow rear disk and full float kits abs jimny |
Original wheel bearing should be discarded - that's what makes the axle fully floating. Steve. |
|
| Author: | shep [ Sat May 14, 2016 4:36 pm ] |
| Post subject: | Re: Joe blow rear disk and full float kits abs jimny |
Bugger. Ball was right. Cheers |
|
| Author: | 31zook [ Sat May 14, 2016 7:02 pm ] |
| Post subject: | Re: Joe blow rear disk and full float kits abs jimny |
Im unsure on which model you recieved but if you go through my build thread you will see all that i had to modify |
|
| Author: | ball [ Sat May 14, 2016 7:24 pm ] |
| Post subject: | Re: Joe blow rear disk and full float kits abs jimny |
shep wrote: Bugger. Ball was right. Cheers
|
|
| Author: | shep [ Sat May 14, 2016 7:39 pm ] |
| Post subject: | Re: Joe blow rear disk and full float kits abs jimny |
31zook wrote: Im unsure on which model you recieved but if you go through my build thread you will see all that i had to modify Most of the issues I have had so far involve fitting it around the abs bits. The kit must have been for a non abs diff. Even down to one of the stub axle bolts hitting the lumpy bit on the diff where the sensor goes. |
|
| Author: | shep [ Fri Aug 12, 2016 3:21 pm ] |
| Post subject: | Re: Joe blow rear disk and full float kits abs jimny |
Not a chance that this kit can be fitted to a jimny with abs. But pissed off that I have wasted money and time on it |
|
| Author: | alien [ Fri Aug 12, 2016 3:40 pm ] |
| Post subject: | Re: Joe blow rear disk and full float kits abs jimny |
On the up side, at least you can re-sell it to re-coup costs? |
|
| Author: | tanshi [ Fri Aug 12, 2016 3:55 pm ] |
| Post subject: | Re: Joe blow rear disk and full float kits abs jimny |
yeah that's a shame, it can be pretty hard to get the bolt to clear but ive managed it with mine. just need to mill a bit out of the floater adapter on mine to clear the abs bung |
|
| Author: | shep [ Fri Aug 12, 2016 6:14 pm ] |
| Post subject: | Re: Joe blow rear disk and full float kits abs jimny |
I have everything fitting except for the abs ring. Cbf making new axles. |
|
| Author: | shep [ Fri Aug 12, 2016 6:24 pm ] |
| Post subject: | Re: Joe blow rear disk and full float kits abs jimny |
What choices are there for rear disks on a abs jimny? Don't really care to much about full floater. Are there any actual kits that fit and use Nissan callipers? |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|