| auszookers.com https://auszookers.com/forum/ |
|
| Jimny error code diagnosis help https://auszookers.com/forum/viewtopic.php?f=5&t=52963 |
Page 1 of 1 |
| Author: | Back4more [ Thu Aug 11, 2016 7:10 pm ] |
| Post subject: | Jimny error code diagnosis help |
Hi, Ive been having issues with my jimny 98 G13BB not holding idle when cold. It stalls when coming to a stop when engine is still cold. The error codes I got with my mates scan tool are: 64- Shift sol#1 31-MAF sensor voltage high 32-MAF sensor voltage low 41-Ignition signal fail 42- CMP sensor no signal 61- Shift sol#1 open Anyone know where to start? I thought it was the IAC but now im lost and confused. Thanks |
|
| Author: | fordem [ Thu Aug 11, 2016 10:56 pm ] |
| Post subject: | Re: Jimny error code diagnosis help |
Clear the codes and see which ones reappear. The codes you list suggest that at some point an attempt may been made to start the engine with a number of sensors disconnected, sensors may have been unplugged with the ignition on, or, the wiring harness may have been damaged & repaired at some point. Ignore for now the 61 & 64, those are transmission related, if the 41 & 42 are valid faults, the engine should not be running - a 42 is logged if the ECU detects a start signal with no input from the cam position sensor (basically the starter should be turning the engine, but there is no signal from the cam sensor, so the engine isn't turning), the 41 is related to that (the ECU is not seeing ignition feedback when it thinks it should) a 41 will usually result in the ECU killing the injectors to avoid flooding the engine with fuel, the 31 & 32 codes at the same time are interesting - a failed MAF sensor or wiring issue will usually produce one or the other, but to have both simultaneously, I'd say is quite unusual. |
|
| Author: | Back4more [ Fri Aug 12, 2016 11:38 am ] |
| Post subject: | Re: Jimny error code diagnosis help |
Any Idea how to go about resolving? Thanks |
|
| Author: | Gwagensteve [ Fri Aug 12, 2016 11:49 am ] |
| Post subject: | Re: Jimny error code diagnosis help |
Have you cleared the codes and checked what reappeared? |
|
| Author: | Back4more [ Fri Aug 12, 2016 3:06 pm ] |
| Post subject: | Re: Jimny error code diagnosis help |
Yeah it came up with the 64 one. |
|
| Author: | Buckman [ Fri Aug 12, 2016 7:44 pm ] |
| Post subject: | Re: Jimny error code diagnosis help |
If that's all that came back go for a drive and re check for codes. |
|
| Author: | Back4more [ Mon Aug 15, 2016 6:14 pm ] |
| Post subject: | Re: Jimny error code diagnosis help |
Throws a different one every time. Not pin pointing the problem for me... |
|
| Author: | watermouse [ Mon Aug 15, 2016 9:51 pm ] |
| Post subject: | Re: Jimny error code diagnosis help |
What are tool are you reading the codes with? |
|
| Author: | Back4more [ Tue Aug 16, 2016 7:24 pm ] |
| Post subject: | Re: Jimny error code diagnosis help |
Maxidiag Elite |
|
| Author: | watermouse [ Tue Aug 16, 2016 9:01 pm ] |
| Post subject: | Re: Jimny error code diagnosis help |
I believe there are issues with scanning EFI Suzukis of this vintage with anything other than Suzuki scan tools. It may be giving you garbage results. You can flash the stored error codes on the check engine light by jumping a connector under the glovebox with a paperclip. The details for this procedure are in the FSM. Codes are cleared by disconnecting the positive battery terminal for a minute. |
|
| Author: | Back4more [ Wed Aug 17, 2016 11:49 am ] |
| Post subject: | Re: Jimny error code diagnosis help |
It did read that i was doing 119km/hr when stationary and coolant temp at -50*C |
|
| Author: | Gwagensteve [ Wed Aug 17, 2016 12:21 pm ] |
| Post subject: | Re: Jimny error code diagnosis help |
Ok. Abandon scan tool and take it for a drive. Is it throwing the check engine light? |
|
| Author: | Back4more [ Fri Aug 19, 2016 9:01 am ] |
| Post subject: | Re: Jimny error code diagnosis help |
Not since I cleared it |
|
| Author: | Gwagensteve [ Fri Aug 19, 2016 10:00 am ] |
| Post subject: | Re: Jimny error code diagnosis help |
No problem then. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|