Here is a screen shot from the FSM:
| auszookers.com https://auszookers.com/forum/ |
|
| Engine removal from 1999 baleno 2WD MT G16B https://auszookers.com/forum/viewtopic.php?f=5&t=54318 |
Page 1 of 1 |
| Author: | davemcgrath [ Sun Jun 18, 2017 2:54 pm ] |
| Post subject: | Engine removal from 1999 baleno 2WD MT G16B |
Going through steps in FSM for Baleno SY416, to remove G16B motor. It's a 2WD MT car. I'm nearly there but: Cannot find the clutch operating cylinder. Do I have to remove this? Cannot locate the propeller shaft in order to disconnect it. I feel pretty stupid but I can't see it there anywhere. It's supposed to be on the transmission case flange. Help would be appreciated. Dave |
|
| Author: | Gwagensteve [ Sun Jun 18, 2017 5:38 pm ] |
| Post subject: | Re: Engine removal from 1999 baleno 2WD MT G16B |
Driveshafts run to each front wheel and from memory they just pull out (circlips) can't recall where the clutch runs to, but it will be on the bellhousing, so on the LHS of the car down low. |
|
| Author: | BlueSuzy [ Sun Jun 18, 2017 5:47 pm ] |
| Post subject: | Re: Engine removal from 1999 baleno 2WD MT G16B |
davemcgrath wrote: Going through steps in FSM for Baleno SY416, to remove G16B motor. It's a 2WD MT car. I'm nearly there but: Cannot find the clutch operating cylinder. Do I have to remove this? Cannot locate the propeller shaft in order to disconnect it. I feel pretty stupid but I can't see it there anywhere. It's supposed to be on the transmission case flange. Help would be appreciated. Dave Clutch is cable, The last one i did, Just cut the axles with a grinder. They are made of cheese |
|
| Author: | davemcgrath [ Sun Jun 18, 2017 5:57 pm ] |
| Post subject: | Re: Engine removal from 1999 baleno 2WD MT G16B |
Thanks for the answers, I was in a mad rush to get the Baleno engine out by dark (I'm working outdoor / not undercover) and I only had use of the crane until the end of today. I think it must be a cable type clutch so there is no hydraulic system. As for the propeller shaft, still a bit confused about that, but as you were saying if I can remove the driveshafts then that should take care of it. Ran out of time, but I can get the crane back soon so I'll get to take another look at it next weekend. |
|
| Author: | Gwagensteve [ Sun Jun 18, 2017 6:00 pm ] |
| Post subject: | Re: Engine removal from 1999 baleno 2WD MT G16B |
I'm a bit confused about the use of the term "propellor shaft"- I suspect it's referring to the short shaft that runs from gearbox to the drivers side CV, so it runs beside the sump. Can't recall what it attaches too. |
|
| Author: | davemcgrath [ Sun Jun 18, 2017 6:23 pm ] |
| Post subject: | Re: Engine removal from 1999 baleno 2WD MT G16B |
Here is a screen shot from the FSM:
|
|
| Author: | BlueSuzy [ Mon Jun 19, 2017 12:49 pm ] |
| Post subject: | Re: Engine removal from 1999 baleno 2WD MT G16B |
You have the wrong manual. That looks like a jimny rear shaft |
|
| Author: | davemcgrath [ Mon Jun 19, 2017 7:07 pm ] |
| Post subject: | Re: Engine removal from 1999 baleno 2WD MT G16B |
I've been working out of a this baleno manual, pages 315 - 318 apply to engine removal. https://docs.google.com/viewer?a=v&pid=sites&srcid=ZGVmYXVsdGRvbWFpbnxzdXp1a2lidWlsZHBob3Rvc3xneDo1ZGVhMDE3YWVjZjlhMWM |
|
| Author: | Blkfxx [ Mon Jun 19, 2017 7:40 pm ] |
| Post subject: | Re: Engine removal from 1999 baleno 2WD MT G16B |
 
|
|
| Author: | fordem [ Mon Jun 19, 2017 11:07 pm ] |
| Post subject: | Re: Engine removal from 1999 baleno 2WD MT G16B |
Balenos were available AWD - that diagram shows the "propeller shaft" on the AWD version, your 2WD vehicle won't have one. |
|
| Author: | davemcgrath [ Wed Jun 21, 2017 6:45 pm ] |
| Post subject: | Re: Engine removal from 1999 baleno 2WD MT G16B |
Yes, you're right fordem I should've twigged sooner. Usually FSMs say "ïf equipped" for non standard options but not in this case, so I wasted quite a bit of time trying to work that out. Frustrating, as I was trying to get the motor out by the end of Sunday. I'll be better prepared when I have another crack this Friday. |
|
| Author: | davemcgrath [ Fri Jun 23, 2017 8:38 am ] |
| Post subject: | Re: Engine removal from 1999 baleno 2WD MT G16B |
Got back under the Baleno this morning to remove those driveshafts. After knocking the joint apart with a hammer no clips to be found  Must be a different type of drive shaft. 
|
|
| Author: | davemcgrath [ Fri Jun 23, 2017 12:51 pm ] |
| Post subject: | Re: Engine removal from 1999 baleno 2WD MT G16B |
No problem, drive shafts are now disconnected. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|