Any hydraulic/pnematic place should have a new grubscrew to suit your needs, or try boltmaster up the rd from yours.
Or u can eat my dick and i will give you one
Unsure about the hex/bolt head ones..
| auszookers.com https://auszookers.com/forum/ |
|
| drain plug halp! https://auszookers.com/forum/viewtopic.php?f=5&t=5936 |
Page 1 of 1 |
| Author: | lump_a_charcoal [ Sun Aug 09, 2009 5:56 pm ] |
| Post subject: | drain plug halp! |
I tried to get the front diff drain plug undone, but the last few people to do it munted it so badly it now has a round hole instead of square... ANyway I'll get my mechanic to weld a nut on and remove it. The bit I need help with is which drain plug it can be replaced with that is not a square hole type, but an external hex type. I heard a while back that there was a magnetic one around, but couldn't find which one it is... |
|
| Author: | shep [ Sun Aug 09, 2009 6:18 pm ] |
| Post subject: | Re: drain plug halp! |
weld a nut to the plug and then put a brass washer on it and keep using it. mine has been undone stacks of times since i fixed it. |
|
| Author: | keechox [ Sun Aug 09, 2009 10:16 pm ] |
| Post subject: | Re: drain plug halp! |
i think one of mine is magnetic, so they are deffinately around. might be the transfer plug? |
|
| Author: | lump_a_charcoal [ Sun Aug 09, 2009 10:20 pm ] |
| Post subject: | Re: drain plug halp! |
All mine are magnetic, but I am after a hex shaped one, not a square key.. |
|
| Author: | shep [ Sun Aug 09, 2009 10:23 pm ] |
| Post subject: | Re: drain plug halp! |
does yours have a flat surface for a seal or is it the tapered one? |
|
| Author: | BlueSuzy [ Sun Aug 09, 2009 10:23 pm ] |
| Post subject: | Re: drain plug halp! |
Any hydraulic/pnematic place should have a new grubscrew to suit your needs, or try boltmaster up the rd from yours. Or u can eat my dick and i will give you one
Unsure about the hex/bolt head ones.. |
|
| Author: | lump_a_charcoal [ Sun Aug 09, 2009 10:26 pm ] |
| Post subject: | Re: drain plug halp! |
shep wrote: does yours have a flat surface for a seal or is it the tapered one?
I could tell you if I could get it out! |
|
| Author: | lump_a_charcoal [ Sun Aug 09, 2009 10:27 pm ] |
| Post subject: | Re: drain plug halp! |
BlueSuzy wrote: Any hydraulic/pnematic place should have a new grubscrew to suit your needs, or try boltmaster up the rd from yours.
Or u can eat my dick and i will give you one Unsure about the hex/bolt head ones.. Hmm tempting, but I try not to snack... |
|
| Author: | kenn [ Sun Aug 09, 2009 10:39 pm ] |
| Post subject: | Re: drain plug halp! |
May be have a look at LJ one's .
|
|
| Author: | shep [ Sun Aug 09, 2009 11:30 pm ] |
| Post subject: | Re: drain plug halp! |
lump_a_charcoal wrote: shep wrote: does yours have a flat surface for a seal or is it the tapered one? I could tell you if I could get it out! you don't need it out to see what type it is. if it is the type that has a flat to seal on the outside of the diff housing they come out easy as if you give it a tap with a cold chisel.
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|