| Author |
Message |
deano
Joined: Mon Jul 06, 2009 11:30 pm Posts: 1 Location: ipswich
|
 Posted: Wed Jul 08, 2009 1:55 am |
|
|
hi there just wondering if someone could tell me how to adjust a new suzuki sierra clutch cable from scratch.thanks
|
|
|
|
 |
royce

omnipotent being
Joined: Sun Jun 11, 2006 11:30 pm Posts: 17216 Location: Pluto
|
 Posted: Wed Jul 08, 2009 11:35 am |
|
put it in, do the nut up till you still have a bit of free play in the clutch arm and your set 
|
|
|
|
 |
Buddy
Joined: Sun Dec 14, 2008 10:30 pm Posts: 34 Location: S.Tas.
|
 Posted: Wed Jul 08, 2009 10:28 pm |
|
Go to http://neh-tech.com. Look up Fixit files. Heaps of Zuki stuff there inc. exactly what you're after. Cheers.
|
|
|
|
 |
BUZOOKA

az supporter
Joined: Sun Aug 30, 2009 11:30 pm Posts: 2659 Location: hobart tasmania
|
 Posted: Mon Oct 26, 2009 5:59 pm |
|
|
yer ive gotta tighten my clutch to im just to lazy to do it at the moment
_________________ -indebt 4x4 club-
nav 32s n winch cust rear
|
|
|
|
 |
SuziBlu
Joined: Mon Sep 14, 2009 11:30 pm Posts: 4268 Location: Eyre Peninsula
|
 Posted: Mon Oct 26, 2009 6:08 pm |
|
Buddy wrote: Go to http://neh-tech.com. Look up Fixit files. Heaps of Zuki stuff there inc. exactly what you're after. Cheers.
I want to do this, but the link no work.
Mine does burn a bit when extreme playing.
|
|
|
|
 |
losfer

az supporter
Joined: Fri Mar 30, 2007 11:30 pm Posts: 977
|
 Posted: Mon Oct 26, 2009 11:18 pm |
|
|
when you fit the new cable , do the adjuster nut up until about 5mm of thread is hanging out past the adjuster nut , you then adjust the 2 nuts at the bracket on the block so that when you apply pressure with your finger on the clutch pedal , you can push the pedal down 20-25mm before you feel any resistance . This is called pedal freeplay.
If you dont have any pedal freeplay , the throwout bearing will be resting against the pressure plate constantly spinning , this is not good , in extreme cases of being too tight , the throwout bearing will be semi disengaging the clutch and will cause the clutch to slip.
too much pedal freeplay will cause the clutch to engage very low (and cause hard selecting of gears and/or crunching), not enough freeplay will cause it to engage high.
as long as you have some pedal freeplay , you can virtually adjust to where you feel comfortable with it engaging.
if you have correct freeplay (20-25mm), and the clutch doesnt disengage fully , you could have a worn clutch , or other issues
does all this make sense ?
|
|
|
|
 |
steak_knife

az supporter
Joined: Fri May 22, 2009 11:30 pm Posts: 21335 Location: Smart Ass Island
|
 Posted: Mon Oct 26, 2009 11:22 pm |
|
SuziBlu wrote: Buddy wrote: Go to http://neh-tech.com. Look up Fixit files. Heaps of Zuki stuff there inc. exactly what you're after. Cheers. I want to do this, but the link no work. Mine does burn a bit when extreme playing.
 that may be the driver.
_________________ I used to be indecisive,
now I'm not so sure.....
|
|
|
|
 |
SuziBlu
Joined: Mon Sep 14, 2009 11:30 pm Posts: 4268 Location: Eyre Peninsula
|
 Posted: Mon Oct 26, 2009 11:28 pm |
|
|
Oh yes, absolutely.
Playing is fun, but only when done to extremes.
hehe.
_________________ Bad decisions make good stories.
|
|
|
|
 |
steak_knife

az supporter
Joined: Fri May 22, 2009 11:30 pm Posts: 21335 Location: Smart Ass Island
|
 Posted: Mon Oct 26, 2009 11:43 pm |
|
SuziBlu wrote: Oh yes, absolutely.
Playing is fun, but only when done to extremes.
hehe.
Is there another way?
If only I could get paid for playing.  Gota be dirty.
_________________ I used to be indecisive,
now I'm not so sure.....
|
|
|
|
 |
|