There is a crush tube that put load on the pinion bearing, very good idea to replace it, I think suzistore sell em, Low range do.
I have used washer's to shim them up, but that was bodge of me
worked but.
| auszookers.com https://auszookers.com/forum/ |
|
| pinion seals https://auszookers.com/forum/viewtopic.php?f=5&t=8133 |
Page 1 of 1 |
| Author: | zookster666 [ Sun Nov 22, 2009 3:45 am ] |
| Post subject: | pinion seals |
My pinion seals have started leaking. So im going to have to change them im just wondering where people have got the seals from and if the front and rear seals are the same. and do they come in a kit? cheers |
|
| Author: | steak_knife [ Sun Nov 22, 2009 3:52 am ] |
| Post subject: | Re: pinion seals |
There is a crush tube that put load on the pinion bearing, very good idea to replace it, I think suzistore sell em, Low range do. I have used washer's to shim them up, but that was bodge of me
worked but. |
|
| Author: | zookster666 [ Sun Nov 22, 2009 3:58 am ] |
| Post subject: | Re: pinion seals |
does the crush tube come in the kit im guessing when i change the seal ill have to reset the backlash on the r&p |
|
| Author: | steak_knife [ Sun Nov 22, 2009 4:09 am ] |
| Post subject: | Re: pinion seals |
zookster666 wrote: does the crush tube come in the kit im guessing when i change the seal ill have to reset the backlash on the r&p
Don't think so. I think, if memory serves, you can replace both in car. Just remove shaft, undo flange nut & remove flange, pull seal out & tube "should" come out, then you just fit the new stuff. I think it can be done in car, but don't hold me to it, If it can than the back lash won't have to be set again as your not moving the crown wheel. |
|
| Author: | zookster666 [ Sun Nov 22, 2009 4:21 am ] |
| Post subject: | Re: pinion seals |
yeah ok sounds good thanks bud |
|
| Author: | steak_knife [ Sun Nov 22, 2009 1:49 pm ] |
| Post subject: | Re: pinion seals |
http://www.suzistore.com.au/shopexd.asp?id=222 Here's a kit, The crush tube is the tube looking thing   
|
|
| Author: | steak_knife [ Sun Nov 22, 2009 1:54 pm ] |
| Post subject: | Re: pinion seals |
Another one, bit cheaper to
http://www.lowrangeoffroad.com/samaxles.htm |
|
| Author: | jdk81 [ Sun Nov 22, 2009 2:38 pm ] |
| Post subject: | Re: pinion seals |
Getting the crush tube tightened correctly is a total pain in the ass. Had to fab up a bracket and pole to bolt to the pinion flange, then get a piece of pipe on the socket. Even being very careful, I still ended up slightly over tightening |
|
| Author: | steak_knife [ Sun Nov 22, 2009 2:52 pm ] |
| Post subject: | Re: pinion seals |
jdk81 wrote: Getting the crush tube tightened correctly is a total pain in the ass.
Had to fab up a bracket and pole to bolt to the pinion flange, then get a piece of pipe on the socket. Even being very careful, I still ended up slightly over tightening Hand brake? If it's still in the car the car has it's own mean's of stopping the pinion & diff from turning.
|
|
| Author: | Scrawny [ Sun Nov 22, 2009 4:10 pm ] |
| Post subject: | Re: pinion seals |
steknig wrote: jdk81 wrote: Getting the crush tube tightened correctly is a total pain in the ass. Had to fab up a bracket and pole to bolt to the pinion flange, then get a piece of pipe on the socket. Even being very careful, I still ended up slightly over tightening Hand brake? If it's still in the car the car has it's own mean's of stopping the pinion & diff from turning.What if it has transmission brake? 
|
|
| Author: | zookster666 [ Sun Nov 22, 2009 4:16 pm ] |
| Post subject: | Re: pinion seals |
Whhel chocks |
|
| Author: | Built4thrashing [ Sun Nov 22, 2009 4:18 pm ] |
| Post subject: | Re: pinion seals |
leave the wheels on the ground and lock in the front hubs and if you have a 2nd person get them to stand on the brakes. This works for undoing t/case nuts. B4T |
|
| Author: | steak_knife [ Sun Nov 22, 2009 4:59 pm ] |
| Post subject: | Re: pinion seals |
ScrawnC wrote: steknig wrote: jdk81 wrote: Getting the crush tube tightened correctly is a total pain in the ass. Had to fab up a bracket and pole to bolt to the pinion flange, then get a piece of pipe on the socket. Even being very careful, I still ended up slightly over tightening Hand brake? If it's still in the car the car has it's own mean's of stopping the pinion & diff from turning.What if it has transmission brake? HULLOW!!!!!! 2nd peddle from the left or right, the middle one!!!! You could use that!!!! 
|
|
| Author: | Brocbeau [ Sun Nov 22, 2009 5:46 pm ] |
| Post subject: | Re: pinion seals |
i have the same problem, with my rear cept its full of swamp water and oil :S, doinga a drain today and gotta replace the rear pinoin seal, advice?? |
|
| Author: | steak_knife [ Sun Nov 22, 2009 8:10 pm ] |
| Post subject: | Re: pinion seals |
Brocbeau wrote: i have the same problem, with my rear cept its full of swamp water and oil :S,
doinga a drain today and gotta replace the rear pinoin seal, advice?? Look up the top of this tread?? 
If it's full of water I'd be getting that out, fill with iol & see if it leak's.. |
|
| Author: | zookster666 [ Sun Nov 22, 2009 9:35 pm ] |
| Post subject: | Re: pinion seals |
both of those kits must be a full diff centre rebuild kit am i right? |
|
| Author: | steak_knife [ Sun Nov 22, 2009 9:36 pm ] |
| Post subject: | Re: pinion seals |
steknig wrote:
No, above the master re build, has the tube,nut & seal. |
|
| Author: | zookster666 [ Sun Nov 22, 2009 9:51 pm ] |
| Post subject: | Re: pinion seals |
are missed that one cheers |
|
| Author: | steak_knife [ Sun Nov 22, 2009 9:54 pm ] |
| Post subject: | Re: pinion seals |
zookster666 wrote: are missed that one cheers
That's ok. |
|
| Author: | Brocbeau [ Sun Nov 22, 2009 10:38 pm ] |
| Post subject: | Re: pinion seals |
should only be the pinoin seal rght?? i hope :S |
|
| Author: | zookster666 [ Sun Nov 22, 2009 10:40 pm ] |
| Post subject: | Re: pinion seals |
With water in your diff you may have caused damage best to pull the center out and Check bearing etc before getting parts |
|
| Author: | steak_knife [ Sun Nov 22, 2009 10:48 pm ] |
| Post subject: | Re: pinion seals |
Brocbeau wrote: should only be the pinoin seal rght?? i hope :S
Have you read any of this?? I even replied to your last question. |
|
| Author: | Brocbeau [ Mon Nov 23, 2009 1:40 am ] |
| Post subject: | Re: pinion seals |
you mentioned a crush tube lad.. |
|
| Author: | steak_knife [ Mon Nov 23, 2009 1:47 am ] |
| Post subject: | Re: pinion seals |
steknig wrote: Brocbeau wrote: i have the same problem, with my rear cept its full of swamp water and oil :S, doinga a drain today and gotta replace the rear pinoin seal, advice?? Look up the top of this tread?? If it's full of water I'd be getting that out, fill with iol & see if it leak's.. I Also said this Watered down oil will leak out where oil won't, it's worth a go. |
|
| Author: | Brocbeau [ Mon Nov 23, 2009 1:56 am ] |
| Post subject: | Re: pinion seals |
yes well.. its ordered any ways, leat ill have a spare i guess, gotta replace diff oil any wayzzzz thanks post whore |
|
| Author: | steak_knife [ Mon Nov 23, 2009 1:57 am ] |
| Post subject: | Re: pinion seals |
Brocbeau wrote: yes well.. its ordered any ways, leat ill have a spare i guess,
gotta replace diff oil any wayzzzz thanks post whore O k.
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|