how do you get it off? i have done 2 clutch's and never replaced this bearing as i couldn't get it off the spigot...
cheers
1200
| auszookers.com https://auszookers.com/forum/ |
|
| throw out/clutch bearing https://auszookers.com/forum/viewtopic.php?f=5&t=8259 |
Page 1 of 1 |
| Author: | 31zook [ Sat Nov 28, 2009 2:36 pm ] |
| Post subject: | throw out/clutch bearing |
how do you get it off? i have done 2 clutch's and never replaced this bearing as i couldn't get it off the spigot... cheers 1200
|
|
| Author: | steak_knife [ Sat Nov 28, 2009 2:52 pm ] |
| Post subject: | Re: spigot bearing |
31zook wrote: how do you get it off? i have done 2 clutch's and never replaced this bearing as i couldn't get it off the spigot...
cheers 1200 Is it in the crank? |
|
| Author: | Scrawny [ Sat Nov 28, 2009 2:58 pm ] |
| Post subject: | Re: spigot bearing |
Slide hammer. If you don't have access to one just make one |
|
| Author: | steak_knife [ Sat Nov 28, 2009 3:02 pm ] |
| Post subject: | Re: spigot bearing |
ScrawnC wrote: Slide hammer. If you don't have access to one just make one
I was going to tell the bushman's trick of a hammer, a grease gun & a bolt. But that will work. 
|
|
| Author: | shep [ Sat Nov 28, 2009 3:39 pm ] |
| Post subject: | Re: spigot bearing |
grease + something that fits in the hole + hammer = a mess and a removed bearing  
|
|
| Author: | Scrawny [ Sat Nov 28, 2009 3:40 pm ] |
| Post subject: | Re: spigot bearing |
steknig wrote: ScrawnC wrote: Slide hammer. If you don't have access to one just make one I was going to tell the bushman's trick of a hammer, a grease gun & a bolt. But that will work. Never had any joy with that method. I found a length of threaded rod and a truck torque rod bush, couple washers and nuts and bingo. Just ground a groove at one end to hook into the bearing. It only works for small bearings though |
|
| Author: | steak_knife [ Sat Nov 28, 2009 3:41 pm ] |
| Post subject: | Re: spigot bearing |
shep wrote: grease + something that fits in the hole + hammer = a mess and a removed bearing
Nothing wrong with a mess if the apprentice cleans it up. Oooppps, I'm an apprentice now.  
|
|
| Author: | 31zook [ Sat Nov 28, 2009 4:44 pm ] |
| Post subject: | Re: spigot bearing |
sorry i may have used the wrong word, this is the bearing im refering to... 
There is a slot on this side of the bearing where the fork is attached i can't get the bearing off the fork attachment.... thanks for all your replys fellas 
|
|
| Author: | Scrawny [ Sat Nov 28, 2009 4:48 pm ] |
| Post subject: | Re: spigot bearing |
Throw out bearing or clutch release bearing. If you pull it out as far as it will come then it just sorta twists off. You'll see the dowel on one side of the fork |
|
| Author: | steak_knife [ Sat Nov 28, 2009 6:38 pm ] |
| Post subject: | Re: spigot bearing |
ScrawnC wrote: Throw out bearing or clutch release bearing. If you pull it out as far as it will come then it just sorta twists off. You'll see the dowel on one side of the fork
Yep, can be a bit tricky but it will come. |
|
| Author: | 31zook [ Sat Nov 28, 2009 7:38 pm ] |
| Post subject: | Re: throw out/clutch bearing |
Hmm maybe im not doing it right but i can't seem to get it off.... grrr |
|
| Author: | Junior_91 [ Sat Nov 28, 2009 10:58 pm ] |
| Post subject: | Re: throw out/clutch bearing |
Pull it off the passneger side the jam a screwdriver down the drivers side of it and bam of it comes haha how do i know this? I did it today |
|
| Author: | Brocbeau [ Sun Nov 29, 2009 12:33 am ] |
| Post subject: | Re: throw out/clutch bearing |
must have some dirty teeths :O |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|