Told ya I may be
Thank's Zook_Fan.
| auszookers.com https://auszookers.com/forum/ |
|
| wt diff conversion https://auszookers.com/forum/viewtopic.php?f=5&t=8876 |
Page 1 of 1 |
| Author: | rogerworkman [ Mon Dec 28, 2009 3:10 am ] |
| Post subject: | wt diff conversion |
hello all i have just started fitting my wt diffs to my 1lt nt lwb and i went to fit the nt diff flanges on the wt diffs and they wouldnt fit the spline is to big.But i thought they were all interchangeable between wt and nt whats the go thanks in advance |
|
| Author: | steak_knife [ Mon Dec 28, 2009 3:38 am ] |
| Post subject: | Re: wt diff conversion |
rogerworkman wrote: hello all i have just started fitting my wt diffs to my 1lt nt lwb and i went to fit the nt diff flanges on the wt diffs and they wouldnt fit the spline is to big.But i thought they were all interchangeable between wt and nt whats the go thanks in advance
Your answer is there, the 1lt's have different center's The 1.3's are the n/t's that the flange's swap across to w/t diff's. I think, could be wrong, but the 1lt diff's bolt up to the w/t housing's, I think the side gear's have to be changed for the axle's tho. Hope that help's |
|
| Author: | Zook_Fan [ Mon Dec 28, 2009 3:40 am ] |
| Post subject: | Re: wt diff conversion |
no your wrong. the 1lt diff's are completely incompatable with the WT stuff. you will have to change the uni's on your shafts. |
|
| Author: | steak_knife [ Mon Dec 28, 2009 3:44 am ] |
| Post subject: | Re: wt diff conversion |
Told ya I may be
Thank's Zook_Fan.
|
|
| Author: | v.w.dave [ Mon Dec 28, 2009 4:20 am ] |
| Post subject: | Re: wt diff conversion |
Can't you just swop the outputs from the transfer cases? Then run W/T shafts? |
|
| Author: | boost=money [ Mon Dec 28, 2009 4:48 am ] |
| Post subject: | Re: wt diff conversion |
run the nt shafts heaps stronger then 1l ones |
|
| Author: | Fatzook [ Mon Dec 28, 2009 5:45 am ] |
| Post subject: | Re: wt diff conversion |
boost=money wrote: run the nt shafts heaps stronger then 1l ones
Beg to differ. Some 1L came out with solid driveshafts. Were very small OD, but solid. This helped with clearance and strength, but made vibration and weight an issue. But really, NT WT or 1L doesn't matter. Unless you are running a bigger motor than G16 EFI, shaft strength is not an issue. You should just get some NT 1.3L drive shafts and swap the yoke off the drive shaft to match the new diff. Cheapest way out. |
|
| Author: | just_cruizin [ Mon Dec 28, 2009 4:32 pm ] |
| Post subject: | Re: wt diff conversion |
Sorry Pete but the solid shafts are no where near as strong as a hollow shaft of the same weight. All the strength is in the outside diameter. The centre of the shaft essentially does nothing for strength either in torsion or bending |
|
| Author: | royce [ Mon Dec 28, 2009 4:36 pm ] |
| Post subject: | Re: wt diff conversion |
if your transfer doesnt have a 4wd switch on it you cant fit 1.3 flanges onto it either, youll have to swap yokes on your 1lt shafts |
|
| Author: | rogerworkman [ Mon Dec 28, 2009 5:44 pm ] |
| Post subject: | Re: wt diff conversion |
thanks for all the replys what ive done is sit the 1lt drive shafts against the wt flanges and drilled them 2 suit hopefully ive done it straight and it wont vibrate |
|
| Author: | steak_knife [ Mon Dec 28, 2009 5:57 pm ] |
| Post subject: | Re: wt diff conversion |
rogerworkman wrote: thanks for all the replys what ive done is sit the 1lt drive shafts against the wt flanges and drilled them 2 suit hopefully ive done it straight and it wont vibrate
That's what I want to do to the Lil wagon, but was advised against it. 
To me that is still strong enough, if you look at yoke's or drive shaft spacer's that are sold thay have multiple hole's in em. I have also drilled in the past with no ill effect's & a bombed 250 cross flow has just a touch more power than a Zook.(not as reliable tho) |
|
| Author: | kenn [ Mon Dec 28, 2009 6:17 pm ] |
| Post subject: | Re: wt diff conversion |
steknig wrote: rogerworkman wrote: thanks for all the replys what ive done is sit the 1lt drive shafts against the wt flanges and drilled them 2 suit hopefully ive done it straight and it wont vibrate That's what I want to do to the Lil wagon, but was advised against it. To me that is still strong enough, if you look at yoke's or drive shaft spacer's that are sold thay have multiple hole's in em. I have also drilled in the past with no ill effect's & a bombed 250 cross flow has just a touch more power than a Zook.(not as reliable tho) Thats exactly what we did in the LJ to suit vit flanges no problems so far, 5 years and counting. 
|
|
| Author: | rogerworkman [ Tue Dec 29, 2009 1:40 am ] |
| Post subject: | Re: wt diff conversion |
ok its all back together took it 4 a spin in gh and no vibrations at all. and i would think the drive shaft bolts would break b4 the flange would if they have been drilled out. thanks again |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|