i think i have a couple of VRS kits with that gasket in them. if you have no joy let me know
| auszookers.com https://auszookers.com/forum/ |
|
| Another part question https://auszookers.com/forum/viewtopic.php?f=5&t=9419 |
Page 1 of 1 |
| Author: | hrzook [ Mon Jan 25, 2010 8:25 pm ] |
| Post subject: | Another part question |
Hi Fellas I am chasing an exhaust gasket for my Suzuki G16B engine. Autobarn checked 5 gasket books but no joy. The gasket in question is the first joint from the manifold. I have added an image to help ID it. Has anyone obtained one of these from somewhere before? If all else fails what have ppl used to make their own exhaust gaskets? Thanks in advanced HR |
|
| Author: | BUZOOKA [ Mon Jan 25, 2010 9:14 pm ] |
| Post subject: | Re: Another part question |
loks like the mask off stekkys cat but i think u can use sickaflex or soemthing like that to seal the area |
|
| Author: | zookfun [ Mon Jan 25, 2010 9:15 pm ] |
| Post subject: | Re: Another part question |
maybe try an exhaust shop or a shop that focuses more on car parts, good luck! |
|
| Author: | Ben_Sierra [ Mon Jan 25, 2010 9:20 pm ] |
| Post subject: | Re: Another part question |
http://suzistore.com.au/shopexd.asp?id=360 Something like this perhaps? |
|
| Author: | mnemonix [ Mon Jan 25, 2010 9:29 pm ] |
| Post subject: | Re: Another part question |
I think i've got one in the shed. I'll check when I get home. Worst case any exhaust shop with source one for you (if they don't have it on the shelf already). |
|
| Author: | want33s [ Mon Jan 25, 2010 9:51 pm ] |
| Post subject: | Re: Another part question |
Before I fitted extractors, I got one from Ripco but it needed the outside 2 bolt holes enlarged a little bit. Just ask for a flange gasket for a 94 Vitara G16B. |
|
| Author: | shep [ Mon Jan 25, 2010 9:55 pm ] |
| Post subject: | Re: Another part question |
i think i have a couple of VRS kits with that gasket in them. if you have no joy let me know
|
|
| Author: | Damo [ Mon Jan 25, 2010 10:35 pm ] |
| Post subject: | Re: Another part question |
shep wrote: i think i have a couple of VRS kits with that gasket in them. if you have no joy let me know
Yep I have got one kicking around in the shed somewhere for the same reason. It's up for grabs if you need it. |
|
| Author: | lump_a_charcoal [ Tue Jan 26, 2010 12:50 am ] |
| Post subject: | Re: Another part question |
Or get gasket material and make one? |
|
| Author: | want33s [ Tue Jan 26, 2010 1:04 am ] |
| Post subject: | Re: Another part question |
lump_a_charcoal wrote: Or get gasket material and make one?
It's an exhaust flange gasket...Tinfoil stuff.. I've never seen sheets or rolls of that stuff for sale anywhere. |
|
| Author: | lump_a_charcoal [ Tue Jan 26, 2010 2:23 am ] |
| Post subject: | Re: Another part question |
Auto one up at Toronto used to sell it in a sheet... Just place it over the flange, tap around the edge with a hammer and cut it out. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|