Guys, does anyone have a M14 x 1.5 tap that they can tap a aluminium water temp adapter for me?
It has a 1/8 hole/thread but need the m14 x 1.5 for the more common size switch I have.
Can travel to you
Thanks
| auszookers.com https://auszookers.com/forum/ |
|
| M14 x 1.5 Tap https://auszookers.com/forum/viewtopic.php?f=5&t=9889 |
Page 1 of 1 |
| Author: | foonji [ Mon Feb 15, 2010 5:57 pm ] |
| Post subject: | M14 x 1.5 Tap |
Guys, does anyone have a M14 x 1.5 tap that they can tap a aluminium water temp adapter for me? It has a 1/8 hole/thread but need the m14 x 1.5 for the more common size switch I have. Can travel to you
Thanks |
|
| Author: | julian [ Mon Feb 15, 2010 10:35 pm ] |
| Post subject: | Re: M14 x 1.5 Tap |
just go buy one from an engineering shop. they are like 20 bucks at most and just use a shifter on it |
|
| Author: | royce [ Mon Feb 15, 2010 10:38 pm ] |
| Post subject: | Re: M14 x 1.5 Tap |
an M14 will be alot more than that!!!! thats an unusual size for water sensors from memory what are you doing? I will try and remember to ask Bruce to look in my box for one |
|
| Author: | foonji [ Mon Feb 15, 2010 11:23 pm ] |
| Post subject: | Re: M14 x 1.5 Tap |
They are around $80-100 and I don't want to buy one for a once off job. It's not actually a sensor for a guage but a switch for the thermo fan to turn it on and off. |
|
| Author: | steak_knife [ Mon Feb 15, 2010 11:44 pm ] |
| Post subject: | Re: M14 x 1.5 Tap |
I'll have a look in my kit tomorrow, need to bring it home any way. 
|
|
| Author: | charlie_brown [ Tue Feb 16, 2010 2:42 am ] |
| Post subject: | Re: M14 x 1.5 Tap |
I'm pretty sure there's one at my work (Rocklea). Dunno about sneaking it out of the place though, so you might have to bring the part in to get done. Send me a PM if you want to follow up. |
|
| Author: | julian [ Tue Feb 16, 2010 4:20 am ] |
| Post subject: | Re: M14 x 1.5 Tap |
fuck no wonder i get in shit when i snap them all the time haha |
|
| Author: | foonji [ Tue Feb 16, 2010 2:49 pm ] |
| Post subject: | Re: M14 x 1.5 Tap |
Thanks guys, Much appreciated
|
|
| Author: | steak_knife [ Tue Feb 16, 2010 10:40 pm ] |
| Post subject: | Re: M14 x 1.5 Tap |
My kit has 2 14x1.25's but no 14x1.5, sorry mate. 
|
|
| Author: | mrw82 [ Wed Feb 17, 2010 1:19 am ] |
| Post subject: | Re: M14 x 1.5 Tap |
if you don't have any luck from anyone else I can borrow one from work for ya. |
|
| Author: | Damo [ Wed Feb 17, 2010 1:23 pm ] |
| Post subject: | Re: M14 x 1.5 Tap |
I bought a big tap a while back, I think it was M18x1.5. When I was looking there were really expensive ones, they might have been cobalt or something, then there were cheaper ones. I bought the cheaper one and it was HSS. As long as you aren't trying to tap stainless or high carbon steel you should be OK with a HSS one. The one I bought was $30-40, and it tapped cast iron no problems. Tap Magic is good stuff. |
|
| Author: | foonji [ Wed Feb 17, 2010 3:00 pm ] |
| Post subject: | Re: M14 x 1.5 Tap |
Been sorted, Charlie_Brown is helping me out with it. Thanks again. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|