auszookers.com
https://auszookers.com/forum/

Sierra bits
https://auszookers.com/forum/viewtopic.php?f=7&t=20600		 Page 1 of 1
Author:  boostedbrick [ Sat Apr 02, 2011 1:06 am ]
Post subject:  Sierra bits
Have the following. 2pin WT center.. Needs bearings. $80
22spline WT CVs/axels $50(make an offer :wink: ) Only long side left
Clutch, aftermarket replacment. Alot of meat left on the clutch plate, good pressure plate.. USED, $50
G13a, no carby or alt. But otherwise complete. Good for parts. Has new fuel pump.. Bottom end is shagged. Any parts off it are free.. Has sump/pickup
WT fuel tank.. Very minimal dints,(still be 39liters), tiny bit of rust staining inside, will need flush. $sold...
WT tow bar, some rust needs paint. $30
Brand new webber 32/36 $150.. Brought new back in '02 for 320.. sat on a shelf since.
G13A/B rocker cover gasket.. cork... Free
Left hand door, damaged with good glass. Free
G16b dizzy.. No cap/button. $40


Pick up only. Browns plains way.. open to offers..
Author:  tonyevans [ Sat Apr 02, 2011 1:21 am ]
Post subject:  Re: Sierra bits
Does the Webber have a Suzuki adapter? Will you post to western NSW?
Author:  boostedbrick [ Sat Apr 02, 2011 1:27 am ]
Post subject:  Re: Sierra bits
Doesnt have adapter... Brought it before i had a sierra.. If your still keen your looking at around $20 postage to Dubbo..
Author:  reallyuted [ Sat Apr 02, 2011 3:17 am ]
Post subject:  Re: Sierra bits
i only need the short side axel with cv if you want to sell them seperate? how much cheers
Author:  lump_a_charcoal [ Sat Apr 02, 2011 6:27 am ]
Post subject:  Re: Sierra bits
tonyevans wrote:
Will you post to western NSW?


Yes he will!
Author:  boostedbrick [ Sat Apr 02, 2011 6:44 am ]
Post subject:  Re: Sierra bits
reallyuted wrote:
i only need the short side axel with cv if you want to sell them seperate? how much cheers


If theres no interest in both in a few days ill let you know.
Author:  boostedbrick [ Sat Apr 02, 2011 6:45 am ]
Post subject:  Re: Sierra bits
lump_a_charcoal wrote:
tonyevans wrote:
Will you post to western NSW?


Yes he will!


Yerp, i just qouted Dubbo as the website wont accept western NSW...


And theres an adapter
http://cgi.ebay.com.au/SUZUKI-SIERRA-VI ... 3f004a3b76
Author:  Bruce [ Sat Apr 02, 2011 6:46 am ]
Post subject:  Re: Sierra bits
Where abouts in Brisbane are you mate?
Author:  boostedbrick [ Sat Apr 02, 2011 6:47 am ]
Post subject:  Re: Sierra bits
Browns plains...
Author:  Bruce [ Sat Apr 02, 2011 6:48 am ]
Post subject:  Re: Sierra bits
Thanks. Can never have enough CV's but bit too far for them. :-(
Author:  royce [ Sat Apr 02, 2011 7:01 am ]
Post subject:  Re: Sierra bits
Bruce wrote:
Thanks. Can never have enough CV's but bit too far for them. :-(


I knew youd be in here soon enough sniffing out cv's :lol:
Author:  Bruce [ Sat Apr 02, 2011 7:16 am ]
Post subject:  Re: Sierra bits
royce wrote:
Bruce wrote:
Thanks. Can never have enough CV's but bit too far for them. :-(


I knew youd be in here soon enough sniffing out cv's :lol:


You think I have enough, don't you :oops:
Author:  boostedbrick [ Sat Apr 02, 2011 7:30 am ]
Post subject:  Re: Sierra bits
Its only an hour here from the northside Bruce.. or 2 in traffic :lol:
Author:  Bruce [ Sat Apr 02, 2011 7:37 am ]
Post subject:  Re: Sierra bits
True mate I know :-)
Author:  reallyuted [ Sat Apr 02, 2011 9:25 pm ]
Post subject:  Re: Sierra bits
pm sent
Author:  boostedbrick [ Sun Apr 03, 2011 2:52 am ]
Post subject:  Re: Sierra bits
Open to offers... This stuff aint any use to me around here.
Author:  fatz [ Mon Apr 04, 2011 5:14 am ]
Post subject:  Re: Sierra bits
do you have a flywheel by anychance?
Author:  boostedbrick [ Mon Apr 04, 2011 7:10 am ]
Post subject:  Re: Sierra bits
Nar mate.
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/