auszookers.com
https://auszookers.com/forum/

Finished Rebuild, Clearing out the rest. Ipswich QLD
https://auszookers.com/forum/viewtopic.php?f=7&t=31089		 Page 1 of 1
Author:  Dark Wolf [ Sun Mar 11, 2012 12:38 pm ]
Post subject:  Finished Rebuild, Clearing out the rest. Ipswich QLD
I have recently finished the re-construction of a 1986 SJ-50 out of at least 3 other Sierra's, and I have a large surplus of parts that I am interested in getting rid of. I am new to all this, so I will give the best descriptions I can, however, as I am unsure of the exact cars that all my parts came from, I can only provide you with their era.

From 1991-1995 vehicle(s):
Front axel
Rear axel
Complete set of standard leaf springs
Chassis
1.3L Carb Engine (Crank shaft turns, but am unsure if it actually runs, includes cluch plate and disk. Carb and manifold not included)
Transfer Case (selects all settings, can turn by hand)
5 Speed Gear box (selects all settings, can turn by hand)
Complete Set of Drive Shafts (One UV joint disassembled, all parts included)
Steering arm, box and column
Instrument Cluster
Wiring loom (both halves)
Front Left quarter panel (the side with the jack holder)
Tailgate
Two bonnets (one black, one yellow(from 1986))
Starter motor and two ignition coils
Set of front disk break calipers and break lines
Two front grills, both early style (both unbroken)

From 1986 vehicle:
Body with tailgate (Yellow, minor deformation caused by some kind of roof impact. Would suite rock crawler project)
Fiberglass canopy (Front section only)
Upper front panel with attached supports (Yellow, the panel that goes above the grill)
Lower front panel (Yellow)

I also have a large number of smaller components such as trimming, attachments and fixtures, message for details if interested.

Pricing:
Engine and Chassis: $150 each
All other drive train/steering/suspension components: $100 each component
All exterior paneling components (includes body): $50 each component

All parts will be sold in the lots listed above, in AS IS condition.
All prices are negotiable, and images will be sent if requested.
All items over 1kg are pickup from Ipswich, Queensland, Australia.

Also, though my project is now completed, I am still missing the plastic or metal strip (unsure) that goes along the top of the windscreen to hold the front of the soft top down. This is the last part I am attempting to track down, so if anyone has one of these lying around, feel free to give us a bell.

Thanks for your time
Author:  mrgtt34 [ Sun Mar 11, 2012 6:15 pm ]
Post subject:  Re: Finished Rebuild, Clearing out the rest. Ipswich QLD
have u got a transfer case mate and how much
Author:  Dark Wolf [ Sun Mar 11, 2012 7:35 pm ]
Post subject:  Re: Finished Rebuild, Clearing out the rest. Ipswich QLD
Yep mate, got the transfer case. As it is a standard drive train component, its $100 neat.
Author:  burls [ Mon Mar 12, 2012 7:56 am ]
Post subject:  Re: Finished Rebuild, Clearing out the rest. Ipswich QLD
Gidday Mate

might have that strip if you still need it. I'll have a look today. I'm interested in the front LH guard and jack shaft if you have one

cheers

Gav
Author:  Dark Wolf [ Mon Mar 12, 2012 8:04 am ]
Post subject:  Re: Finished Rebuild, Clearing out the rest. Ipswich QLD
Thanks man, I’m not entirely sure what you mean by jack shaft, but I do have the complete LH (Looking from the back) front guard, it’s a dark grey colour, and only has a little rust in that little spot just below the head light where they all go. If that is what you are looking for, I would be interested in a 1:1 trade for the soft top strip and its mounting screws.
Author:  burls [ Mon Mar 12, 2012 9:34 am ]
Post subject:  Re: Finished Rebuild, Clearing out the rest. Ipswich QLD
Found it so deal. The shaft I'm after is the one from the gearbox to the transfer case
Pm your number and I'll organise pick I'm off today and tomorrow
Author:  ca18zook [ Thu Mar 15, 2012 4:33 pm ]
Post subject:  Re: Finished Rebuild, Clearing out the rest. Ipswich QLD
what your nunber mate as ill grab the black bonnet off u
Trent
Author:  Dark Wolf [ Fri Mar 16, 2012 12:12 am ]
Post subject:  Re: Finished Rebuild, Clearing out the rest. Ipswich QLD
The rear axle, front quarter pannel, and jack shaft have all been sold.
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/