Ok so I have 3 sets available. Cost me $200 to make 4 sets so I'm not trying to make a profit on these. At $40 a set.
| auszookers.com https://auszookers.com/forum/ |
|
| Seirra on Jimny Hub rings, adaptors $40 https://auszookers.com/forum/viewtopic.php?f=7&t=44605 |
Page 1 of 1 |
| Author: | Gromet [ Thu Jan 09, 2014 4:47 pm ] |
| Post subject: | Seirra on Jimny Hub rings, adaptors $40 |
Will have 4 sets available next week. bolts will cost extra. 8mm thick water jet cut aluminum. PM me for dibs. Located in Lowood but can put anywhere in Australia. Hayden 0422238170 |
|
| Author: | Gromet [ Thu Jan 23, 2014 8:17 pm ] |
| Post subject: | Re: Seirra on Jimny Hub rings, adaptors $40 |
can do them with bolts for $50 |
|
| Author: | shep [ Thu Jan 23, 2014 9:23 pm ] |
| Post subject: | Re: Seirra on Jimny Hub rings, adaptors $40 |
Who's are you copying? |
|
| Author: | Gromet [ Thu Jan 23, 2014 9:31 pm ] |
| Post subject: | Re: Seirra on Jimny Hub rings, adaptors $40 |
The hubs. Getting the spacers made at a place I worked at. Its costing me to much just to make a 1 set so I'm getting another 4 to cover some of my costs. picking them up tomorrow hopefully. |
|
| Author: | Gromet [ Fri Jan 31, 2014 2:11 pm ] |
| Post subject: | Re: Seirra on Jimny Hub rings, adaptors $40 |
Ok so I have 3 sets available. Cost me $200 to make 4 sets so I'm not trying to make a profit on these. At $40 a set.
|
|
| Author: | jimny_timmy [ Sat Feb 01, 2014 10:28 am ] |
| Post subject: | Re: Seirra on Jimny Hub rings, adaptors $40 |
Hate to be a downer dude, but you're better off cutting your axle down. I have personally (and witnessed others) snap the 12.9 high tensile hub bolts completely off with the spacers. It allows a little movement and the bolts load up and the go bang. |
|
| Author: | Gromet [ Sat Feb 01, 2014 11:40 am ] |
| Post subject: | Re: Seirra on Jimny Hub rings, adaptors $40 |
Cutting the axle and hub seal? No thanks. That's why I didn't go the 10mm. They will be fine. I've done the research... |
|
| Author: | Gromet [ Sat Feb 01, 2014 11:41 am ] |
| Post subject: | Re: Seirra on Jimny Hub rings, adaptors $40 |
Don't like hacking the fuck out of cars anyways |
|
| Author: | jimny_timmy [ Sat Feb 01, 2014 11:57 am ] |
| Post subject: | Re: Seirra on Jimny Hub rings, adaptors $40 |
Ok 
|
|
| Author: | 31zook [ Sat Feb 01, 2014 1:27 pm ] |
| Post subject: | Re: Seirra on Jimny Hub rings, adaptors $40 |
Gromet wrote: Cutting the axle and hub seal? No thanks. That's why I didn't go the 10mm. They will be fine. I've done the research... Okay
|
|
| Author: | Zook_Fan [ Sun Feb 02, 2014 6:44 pm ] |
| Post subject: | Re: Seirra on Jimny Hub rings, adaptors $40 |
jimny_timmy wrote: Hate to be a downer dude, but you're better off cutting your axle down. I have personally (and witnessed others) snap the 12.9 high tensile hub bolts completely off with the spacers. It allows a little movement and the bolts load up and the go bang. If they are allowing movement why aren't people making them with undersized holes and then threading them so the hub bolt tightens the hub and the spacer to the axle? Not having a go at you, just seems like a progressive step if movement is the issue |
|
| Author: | Gromet [ Sun Feb 02, 2014 6:54 pm ] |
| Post subject: | Re: Seirra on Jimny Hub rings, adaptors $40 |
Zook_Fan wrote: jimny_timmy wrote: Hate to be a downer dude, but you're better off cutting your axle down. I have personally (and witnessed others) snap the 12.9 high tensile hub bolts completely off with the spacers. It allows a little movement and the bolts load up and the go bang. If they are allowing movement why aren't people making them with undersized holes and then threading them so the hub bolt tightens the hub and the spacer to the axle? Not having a go at you, just seems like a progressive step if movement is the issue Then you would never get them tight. it would be physically impossible. I can see where there coming from, But if there that upset about the spacers maybe they should shoot Bigjimny and jimnybits a few messages to try and really corner the market? I only made a few extras because I couldn't find any when I needed them, Now all of a sudden its locals businesses. |
|
| Author: | jimny_timmy [ Sun Feb 02, 2014 6:55 pm ] |
| Post subject: | Re: Seirra on Jimny Hub rings, adaptors $40 |
It's the extra stress on the bolts that's the issue, not the hole size... Probably more an issue in front locked situations. And to the op/mods, I'm not trying to throw people off buying these... My comments can be deleted if necessary, I was just trying to give a heads up on the issue. |
|
| Author: | Gromet [ Sun Feb 02, 2014 6:59 pm ] |
| Post subject: | Re: Seirra on Jimny Hub rings, adaptors $40 |
jimny_timmy wrote: It's the extra stress on the bolts that's the issue, not the hole size... Probably more an issue in front locked situations. And to the op/mods, I'm not trying to throw people off buying these... My comments can be deleted if necessary, I was just trying to give a heads up on the issue. No stress mate... I didn't want to get my hubs and axles machined... I'm not intending on getting massive tires or locking diffs... so these should be fine for intermediate 4wding. 
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|