Its only inspected and certified in Qld, no good for any other state.
Would need to be engineered again in any other state for a blue slip/road worthy, $$$$$$
Good luck with the sale
| auszookers.com https://auszookers.com/forum/ |
|
| 1988 Suzuki Sierra Hard-top (Unfinished Project) LOC:VIC https://auszookers.com/forum/viewtopic.php?f=7&t=50691 |
Page 1 of 1 |
| Author: | Delphaeus [ Sun Aug 02, 2015 6:25 pm ] |
| Post subject: | 1988 Suzuki Sierra Hard-top (Unfinished Project) LOC:VIC |
1988 Suzuki Sierra - Runs well, but not roadworthy. Price $2000 for quick sale. Must be gone by the end of this weekend (Oct 2) Pick up only. You will need to tow this as it is NOT DRIVEABLE Location - Victoria, Carrum Downs. PM me for address or more details. Photos https://goo.gl/photos/2T5Me7mynZSiGRGZ9 Additional Details It has a 1.6L EFI G16A engine and a 1L surge tank under the hood. Its also had a significant suspension and body lift fitted to it (around 4 inches all up) The engine and the front bucket seats are blue plated (Engineered/Approved in QLD). It has some surface rust in a few spots over the body, but all serious rust has already been repaired. What I've done: Replaced Shock absorbers Replaced radiator with brand new honda civic radiator (with electric fan and shroud) Installed rock slider to one side of the car (other side needs minor modifications as some lines interfere with the bolt on location) Stripped, repaired and Painted the inner floor of the car with Rustbullet Covered the entire inner floor of the car with Dynamat Xtreme Replaced MDF door liners with Aluminium checkerplate Replaced dash with custom made aluminium dash Installed ECU inside the cabin, just under the dash. Installed Amplifier for radio. What needs to be done for roadworthy: Fit flares to wheel arches (i have 4 x jeep flares) Fit gauges to dash (I was going to get tablets and use a OBD2 link) Install Seats Reinstall handbrake cable Reinstall windscreen wipers and steering wheel What is included with the car: 2 sets of 4 wheels, (31" and standard) 2 Front bucket seats - have been fitted before 1 rear double bench seat - needs modification before fitting Raptor ute-liner paint (i was going to paint the car floor with this) All the parts which were removed from the car, except the plastic dash. |
|
| Author: | Gwagensteve [ Mon Aug 03, 2015 9:45 am ] |
| Post subject: | Re: 1988 Suzuki Sierra Hard-top (Unfinished Project) LOC:VIC |
Blue plate? What does that mean in Victoria? Steve. |
|
| Author: | Delphaeus [ Mon Aug 03, 2015 6:39 pm ] |
| Post subject: | Re: 1988 Suzuki Sierra Hard-top (Unfinished Project) LOC:VIC |
It was blue plated in QLD. I really should have mentioned that somewhere. In QLD It means the modification has been inspected and certified/approved. |
|
| Author: | rwt65 [ Mon Aug 03, 2015 8:57 pm ] |
| Post subject: | Re: 1988 Suzuki Sierra Hard-top (Unfinished Project) LOC:VIC |
Its only inspected and certified in Qld, no good for any other state. Would need to be engineered again in any other state for a blue slip/road worthy, $$$$$$ Good luck with the sale
|
|
| Author: | Delphaeus [ Mon Aug 03, 2015 9:23 pm ] |
| Post subject: | Re: 1988 Suzuki Sierra Hard-top (Unfinished Project) LOC:VIC |
Maybe... but i'd need to check up to be certain... this thread seems to have divided opinions http://www.aussiev8.com.au/legislation- ... d-car.html worst case scenario, i'll just wreck the car... shouldn't be to hard to get a few grand still |
|
| Author: | Delphaeus [ Tue Aug 18, 2015 7:29 pm ] |
| Post subject: | 1988 Suzuki Sierra Hard-top (Unfinished Project) VIC |
1. What I'm selling 1988 Suzuki Sierra Mechanically in great shape however its far from roadworthy. Needs time spent on it. It has a 1.6L EFI G16A engine and a 1L surge tank under the hood. Its also had a significant suspension and body lift fitted to it (around 4 inches all up) The engine and the front bucket seats are QLD Blue Plated. It has some surface rust in a few spots over the body, but all serious rust has already been repaired. Since I've had the car I have done a fair bit of work to the beast, but I'm only about halfway finished and have lost interest. What I've done: Cut out rusted area below the windscreen and welded in new steel. Replaced Shock absorbers Replaced leaking radiator with brand new honda civic radiator (with electric fan and shroud) Installed rock slider to one side of the car (other side needs minor modifications as some lines interfere with the bolt on location) Stripped the inner floor of the car to bare metal, welded up all the excess screw holes from 25 years of things being installed Painted the inner floor of the car with Rustbullet Covered the entire inner floor of the car with Dynamat Xtreme Replaced MDF door liners with Aluminium checkerplate Replaced warped dash with custom made aluminium dash Removed faulty handbrake cable (still needs to be re-installed) Installed ECU inside the cabin, just under the dash. Installed Amplifier for radio. What still needs to be done for roadworthy: (disclaimer: this is my opinion): Fit flares to wheel arches (i have 4 x jeep flares) Fit gauges to dash (I was going to get tablets and use a OBD2 link) Install Seats Repair handbrake Reinstall windscreen wipers and steering wheel What is included with the car: 2 sets of 4 wheels, (31" and standard) 2 Front bucket seats - have been fitted before 1 rear double bench seat - needs modification before fitting Raptor ute-liner paint (i was going to paint the car floor with this) A whole pile of parts that I pulled out of the car Other Details 2. Location - Victoria, Carrum Downs. 3. Pick up only. You will need to tow this as it is NOT DRIVEABLE 4. Price - I want to start with $4000 ONO. At that price i will be losing around half of the money I have put into this car. (the custom dash was $1000 by itself) 5. If you can PM me, that would be great. I'll then PM you back with my mobile number and email. I can also give you my address if you want to come and have a look. 6. Photos Click the following link to see a lot more photos https://plus.google.com/+AshleyWaugh/posts/VHJWcm8svv5 Some photos from that selection are here:   
|
|
| Author: | 4x4xzook [ Thu Aug 20, 2015 10:43 am ] |
| Post subject: | Re: 1988 Suzuki Sierra Hard-top (Unfinished Project) VIC |
looks tidy, good luck. what condition are the 31 tyres in how much tread is left? |
|
| Author: | Jasonvsj80 [ Wed Aug 26, 2015 6:45 pm ] |
| Post subject: | Re: 1988 Suzuki Sierra Hard-top (Unfinished Project) LOC:VIC |
wrecking yet? i would be interested in the 1.6efi and possibly complete front diff if its WT (if the price is right) |
|
| Author: | Jasonvsj80 [ Wed Aug 26, 2015 6:53 pm ] |
| Post subject: | Re: 1988 Suzuki Sierra Hard-top (Unfinished Project) VIC |
if you decide to part it out i would be interested in the 1.6efi and possibly complete front diff if its WT (if the price is right) and some other small bits a pieces! PM me or contact me on 0401034750, mobile prefered! |
|
| Author: | suzukikid [ Wed Aug 26, 2015 8:37 pm ] |
| Post subject: | Re: 1988 Suzuki Sierra Hard-top (Unfinished Project) LOC:VIC |
If you part it I'm keen on front clip..... |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|