| auszookers.com https://auszookers.com/forum/ |
|
| Joe Blow - floater kit and axles https://auszookers.com/forum/viewtopic.php?f=7&t=54056 |
Page 1 of 1 |
| Author: | just_cruizin [ Sun Mar 26, 2017 8:50 am ] |
| Post subject: | Joe Blow - floater kit and axles |
Joe Blow Floater kit and axles to suit Located Northside Brisbane Will post at buyers cost Price: $200 neg Came on a diff I bought, never driven. I'm going a different direction What you see is what you get, all flanges to mount to your diff, seals and axles. You need to supply vitara hubs and all brake components Seals are in good condition, have been pressed out not levered  
|
|
| Author: | just_cruizin [ Sun Mar 26, 2017 2:29 pm ] |
| Post subject: | Re: Joe Blow - floater kit and axles |
Sold |
|
| Author: | Dmfelix [ Mon Mar 27, 2017 2:19 pm ] |
| Post subject: | Re: Joe Blow - floater kit and axles |
Who ever purchased this please be aware these axles are made of cheese, mine broke clean off at the circlip. I'd upgrade to some ADD Engineering Axles or atleast get some as spares 
|
|
| Author: | jono165 [ Mon Mar 27, 2017 2:27 pm ] |
| Post subject: | Re: Joe Blow - floater kit and axles |
Dmfelix wrote: Who ever purchased this please be aware these axles are made of cheese, mine broke clean off simultaneously at the circlip. I'd upgrade to some ADD Engineering Axles or atleast get some as spares Those ones do look to be slightly better machined and less egg shaped than yours though |
|
| Author: | Gwagensteve [ Mon Mar 27, 2017 3:26 pm ] |
| Post subject: | Re: Joe Blow - floater kit and axles |
I was going to ask whether the root of the circle groove was smaller than the OD of the smallest diameter of the axle shaft, but as Jon pointed out, they do look a little better machined than yours. Lets hope that means they were also better designed. |
|
| Author: | VitNick [ Mon Mar 27, 2017 3:45 pm ] |
| Post subject: | Re: Joe Blow - floater kit and axles |
I'll have a measure of them once I have them in hand. So I should have a measure of the circlip groove O.D and a few points of the shafts along their length. Would it be worth running them between centers and checking for runout/ ovalness? Cylindrical grinder can fix the ovalness if any and if there's enough material. |
|
| Author: | tanshi [ Tue Mar 28, 2017 10:05 am ] |
| Post subject: | Re: Joe Blow - floater kit and axles |
just run them till they break and buy replacements from me |
|
| Author: | henno [ Tue Mar 28, 2017 12:45 pm ] |
| Post subject: | Re: Joe Blow - floater kit and axles |
tanshi wrote: just run them till they break and buy replacements from me Do that. The rest of the kit is worth the 200 bucks, so the axles are basically freebies. |
|
| Author: | Gwagensteve [ Tue Mar 28, 2017 3:47 pm ] |
| Post subject: | Re: Joe Blow - floater kit and axles |
Totally agree. |
|
| Author: | VitNick [ Tue Mar 28, 2017 5:53 pm ] |
| Post subject: | Re: Joe Blow - floater kit and axles |
Will do, time to start finding the rest of the required bits |
|
| Author: | just_cruizin [ Tue Mar 28, 2017 6:13 pm ] |
| Post subject: | Re: Joe Blow - floater kit and axles |
I don't see why they would break at the circlip, no load is outside there |
|
| Author: | jdk81 [ Tue Mar 28, 2017 6:31 pm ] |
| Post subject: | Re: Joe Blow - floater kit and axles |
Look again? |
|
| Author: | just_cruizin [ Tue Mar 28, 2017 6:52 pm ] |
| Post subject: | Re: Joe Blow - floater kit and axles |
Yep yep, did pay too much attention pulling the off ha |
|
| Author: | suzukikid [ Thu Mar 30, 2017 7:47 pm ] |
| Post subject: | Re: Joe Blow - floater kit and axles |
This still availiable? Or did it end up selling like the first post says? |
|
| Author: | just_cruizin [ Fri Mar 31, 2017 6:20 am ] |
| Post subject: | Re: Joe Blow - floater kit and axles |
just_cruizin wrote: Sold
|
|
| Author: | suzukikid [ Sat Apr 01, 2017 4:57 pm ] |
| Post subject: | Re: Joe Blow - floater kit and axles |
Bugger |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|