auszookers.com
https://auszookers.com/forum/

URGENT WTB 26 spline LHS Vitara front shaft ~ I GOT 1
https://auszookers.com/forum/viewtopic.php?f=8&t=10341		 Page 1 of 1
Author:  atari4x4 [ Wed Mar 10, 2010 2:42 am ]
Post subject:  URGENT WTB 26 spline LHS Vitara front shaft ~ I GOT 1
Hey Groovers,

I'm chasing a LHS 26 spline shaft out of the front of a Vitara/Grand Vitara, it needs to have the indent in the flange to accept the CV like this:

Image

The 26 spline shafts are thicker & have less taper coming down from the bearing surface like this :lol:
Image

NOT LIKE THIS :(
Image

Let me know what you've got & how much you want!

Thanks
Gus
Author:  Joe [ Wed Mar 10, 2010 2:58 am ]
Post subject:  Re: URGENT WTB 26 spline LHS Vitara front shaft
Hey thats my crocodile in the back ground of that first pic 8O :? :roll: :lol: :cry:
Author:  Polar_Bear [ Wed Mar 10, 2010 4:10 am ]
Post subject:  Re: URGENT WTB 26 spline LHS Vitara front shaft
doesnt actually need the recess in the end, that can get machined out 8)
Author:  ninjadaniel [ Wed Mar 10, 2010 2:26 pm ]
Post subject:  Re: URGENT WTB 26 spline LHS Vitara front shaft
i just threw one of these out! argh
Author:  atari4x4 [ Wed Mar 10, 2010 4:22 pm ]
Post subject:  Re: URGENT WTB 26 spline LHS Vitara front shaft
ninjadaniel wrote:
i just threw one of these out! argh


can you un-throw them out... :? :wink: :roll:
Author:  steak_knife [ Wed Mar 10, 2010 10:47 pm ]
Post subject:  Re: URGENT WTB 26 spline LHS Vitara front shaft
Why not just glue the flange to a machined inner cv??
Author:  atari4x4 [ Wed Mar 10, 2010 10:57 pm ]
Post subject:  Re: URGENT WTB 26 spline LHS Vitara front shaft
that's one way of doing it...

the CAD drawings that Polar_Bear has & is getting machined up is a bearing carrier & seal, similar to the CALMINI Anvil set up. Then you get a LHS shaft & chop it down & respline it back to 26 spline.
Author:  steak_knife [ Wed Mar 10, 2010 11:15 pm ]
Post subject:  Re: URGENT WTB 26 spline LHS Vitara front shaft
Nice :P

I was stupidly going to say that you don't need 26 spline since you are re spline'n it, then my computer froze, & in that time my brain un froze & I understood the need for 26. 8O :? :roll: :wink: :lol: :lol:

Some time's delay's in technology stop you from saying stupid things.. :P
Author:  atari4x4 [ Wed Mar 10, 2010 11:59 pm ]
Post subject:  Re: URGENT WTB 26 spline LHS Vitara front shaft
SORTED, thanks to DJ710 Armsup
Author:  Warpspeed [ Mon Apr 12, 2010 2:57 pm ]
Post subject:  Re: URGENT WTB 26 spline LHS Vitara front shaft ~ I GOT 1
Can anyone here tell me the length of one of the LHS front drive shafts?
Author:  atari4x4 [ Mon Apr 12, 2010 3:30 pm ]
Post subject:  Re: URGENT WTB 26 spline LHS Vitara front shaft ~ I GOT 1
the original length is 392mm & the cut down length is 114.5mm
Author:  Warpspeed [ Mon Apr 12, 2010 3:52 pm ]
Post subject:  Re: URGENT WTB 26 spline LHS Vitara front shaft ~ I GOT 1
atari4x4 wrote:
the original length is 392mm & the cut down length is 114.5mm


Thanks Atari
Author:  atari4x4 [ Mon Apr 12, 2010 4:06 pm ]
Post subject:  Re: URGENT WTB 26 spline LHS Vitara front shaft ~ I GOT 1
hmmmm, what are planning on doing?
Author:  Warpspeed [ Mon Apr 12, 2010 4:38 pm ]
Post subject:  Re: URGENT WTB 26 spline LHS Vitara front shaft ~ I GOT 1
atari4x4 wrote:
hmmmm, what are planning on doing?


Oh dear ! ':oops:'
I was afraid someone might ask that question, it is a very long story, but they say confession is good for the soul.

I am hoping to eventually build a 4WD Hot Rod (29 Ford) and am researching and scrounging parts for a double wishbone independent front suspension.
I now have most of it figured out, and all the bits that go round and round are basically all from a Nissan Skyline GTR, including the front diff and drive shafts, hubs, brakes and so on....

That will all work just as it is, the front track will be the same as a GTR, but the two front GTR drive shafts are different lengths, and that will look ugly because it will all be exposed to view, and will look different on each side.

Now the interesting bit.

Only two companies make differentials in Japan, Toyota, and Fuji Heavy Industries. Toyota diffs are unique, but every other Japanese vehicle uses the Fuji diff in one form or another. So what very few people know, is that there is MASSIVE unexpected interchangeability between many quite seemingly unrelated Japanese vehicles.

So what I am trying to do is discover what might fit with regard to spline count and various drive shaft lengths. The same Fuji R160 diff center used in a Zuke is also used in some Mazda, Subaru, Datsun, and Nissan vehicles.

Not every single part is interchangeable, but some definitely are. It is all a bit of a stab in the dark really, but it is a challenging project that is proving to be very interesting.
The GTR shares the exact same 22 spline shaft end as the Zuke that fits into the outer CV joints. Also the R160 diff center is the same size in GTR and Zuke. So fitting some Zuke front drive bits to my project may be a distinct possibility.

believe it or not !
Author:  atari4x4 [ Mon Apr 12, 2010 4:42 pm ]
Post subject:  Re: URGENT WTB 26 spline LHS Vitara front shaft ~ I GOT 1
w0w that sounds like a deadly project & i replied to your wanted ad.
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/