ummm do you realise this is a WANTED ad....
| auszookers.com https://auszookers.com/forum/ |
|
| arb bar https://auszookers.com/forum/viewtopic.php?f=8&t=17626 |
Page 1 of 1 |
| Author: | smiffkid [ Sun Dec 19, 2010 11:30 am ] |
| Post subject: | arb bar |
for jimny. the main winch cradle must be straight, the rest can be in any condition |
|
| Author: | monley [ Sun Dec 19, 2010 11:35 am ] |
| Post subject: | Re: arb bar |
Should be right as long as the mounts are good and there are no cracked welds. Have you found a second hand one? |
|
| Author: | atari4x4 [ Sun Dec 19, 2010 11:38 am ] |
| Post subject: | Re: arb bar |
ummm do you realise this is a WANTED ad....
|
|
| Author: | monley [ Sun Dec 19, 2010 11:39 am ] |
| Post subject: | Re: arb bar |
Do now! |
|
| Author: | smiffkid [ Sun Dec 19, 2010 11:42 am ] |
| Post subject: | Re: arb bar |
yea i know, i want an arb bar. |
|
| Author: | monley [ Sun Dec 19, 2010 11:44 am ] |
| Post subject: | Re: arb bar |
Don't you already have a bar and a which mounted? |
|
| Author: | smiffkid [ Sun Dec 19, 2010 11:46 am ] |
| Post subject: | Re: arb bar |
i have a gay aluminum bar and i do have a winch cradle correct. but i want to lift my winch higher and get a bar with a bit of strength behind it. plus it must look the goods |
|
| Author: | monley [ Sun Dec 19, 2010 11:52 am ] |
| Post subject: | Re: arb bar |
That's right i remember now ally is gay look at my gay nudge bar. |
|
| Author: | Fatzook [ Sun Dec 19, 2010 12:01 pm ] |
| Post subject: | Re: arb bar |
smiffkid wrote: i have a gay aluminum bar and i do have a winch cradle correct.
but i want to lift my winch higher and get a bar with a bit of strength behind it.plus it must look the goods Then make your own. ARB qualifies neither of these requirements. |
|
| Author: | smiffkid [ Sun Dec 19, 2010 12:14 pm ] |
| Post subject: | Re: arb bar |
i basically just want to use the centre of the bar. i would have to make my own brackets because of the body lift |
|
| Author: | hooki [ Sun Dec 19, 2010 5:08 pm ] |
| Post subject: | Re: arb bar |
why start with an expensive ARB bar then if it's going to be butchered? Surely the guys at perth4x4 could nock something up for you....a nice tube front bar? |
|
| Author: | smiffkid [ Mon Dec 20, 2010 8:57 am ] |
| Post subject: | Re: arb bar |
was just gonna use the centre. i could deffinitly make 1 up. |
|
| Author: | atari4x4 [ Mon Dec 20, 2010 9:03 am ] |
| Post subject: | Re: arb bar |
i'd grab any old cheap ARB winch bar, if you get something like a poohtrol/landcouch at least then it will take a 9000lb winch & chop it up, i think the sierra/jimny will only take the smaller 6000lb warn winches + you'll end up paying heaps for a jimny bar as they are few & far between. |
|
| Author: | smiffkid [ Mon Dec 20, 2010 9:06 am ] |
| Post subject: | Re: arb bar |
yea. other wise ill just fab a tube bar up 1 arvo at work |
|
| Author: | monley [ Mon Dec 20, 2010 9:37 am ] |
| Post subject: | Re: arb bar |
smiffkid wrote: yea. other wise ill just fab a tube bar up 1 arvo at work
Make me one while your there! LOL |
|
| Author: | smiffkid [ Mon Dec 20, 2010 9:58 am ] |
| Post subject: | Re: arb bar |
yea na cause it wont be air bad compatible, but atleast mine wont be a macano set like the 1 u wanted lol |
|
| Author: | monley [ Mon Dec 20, 2010 10:08 am ] |
| Post subject: | Re: arb bar |
Haha funny fucker, i have sort of gone that idea the macano idea now, now i want an ARB bar, or the TSOR( if i lke it). LOL And out door auto will be bringing out a Ally front whinch bar, sliders, rear bar and wheels carrier early next for the jimny. |
|
| Author: | smiffkid [ Mon Dec 20, 2010 10:09 am ] |
| Post subject: | Re: arb bar |
think im gonna go custom, looks better |
|
| Author: | monley [ Mon Dec 20, 2010 10:10 am ] |
| Post subject: | Re: arb bar |
i Would but AIRBAGS!!! |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|