| auszookers.com https://auszookers.com/forum/ |
|
| 3 cyl 2 stroke motor https://auszookers.com/forum/viewtopic.php?f=8&t=21754 |
Page 1 of 1 |
| Author: | tonyevans [ Sun May 08, 2011 4:38 am ] |
| Post subject: | 3 cyl 2 stroke motor |
Looking for a good crankshaft assembly or a whole 3 cyl 2 stroke motor for a LJ50 |
|
| Author: | tonyevans [ Wed May 11, 2011 1:00 am ] |
| Post subject: | Re: 3 cyl 2 stroke motor |
Come on Guys - I know you have heaps of them laying around - Someone must need the room - Tony |
|
| Author: | Fity [ Wed May 11, 2011 5:58 am ] |
| Post subject: | Re: 3 cyl 2 stroke motor |
tonyevans wrote: Come on Guys - I know you have heaps of them laying around - Someone must need the room - Tony
We all need more room for more parts. 
After 30 + years of zinging around a good bottom end would be hard to find. Rebuild what you have is probably going to be the best bet. |
|
| Author: | tonyevans [ Wed May 11, 2011 6:04 am ] |
| Post subject: | Re: 3 cyl 2 stroke motor |
Fity wrote: tonyevans wrote: Come on Guys - I know you have heaps of them laying around - Someone must need the room - Tony We all need more room for more parts. After 30 + years of zinging around a good bottom end would be hard to find. Rebuild what you have is probably going to be the best bet. If I can find someone to do it AND the parts 
|
|
| Author: | RIKSTR [ Wed May 11, 2011 9:06 am ] |
| Post subject: | Re: 3 cyl 2 stroke motor |
Hey Tony, Give izook a PM he has a running 2stroker that he wants to get rid of. Dont laugh it runs and is mech in good nick just teh body is toast. A good reason why you shouldn't let kids have a free run with a farm car. 
Yes it goes stop laughing 
|
|
| Author: | tonyevans [ Wed May 11, 2011 11:46 am ] |
| Post subject: | Re: 3 cyl 2 stroke motor |
Thanks RIKSTR - PM sent - Would you have an Email address for him? |
|
| Author: | Fity [ Thu May 12, 2011 2:02 am ] |
| Post subject: | Re: 3 cyl 2 stroke motor |
Can't believe how good the seats are, I have a hard top with much worse seats. 
|
|
| Author: | tonyevans [ Thu May 12, 2011 2:05 am ] |
| Post subject: | Re: 3 cyl 2 stroke motor |
I think that's just the covers surviving a bit |
|
| Author: | RIKSTR [ Thu May 12, 2011 3:49 am ] |
| Post subject: | Re: 3 cyl 2 stroke motor |
PM sent |
|
| Author: | 303zuke [ Sun May 15, 2011 1:31 am ] |
| Post subject: | Re: 3 cyl 2 stroke motor |
This is currently on e-bay, but although the cylinder casting says LJ50, this didn't come out of an LJ50 4x4. It is a late production low pollution model without the oil feed to the cylinders, as discussed on page 2 of the LJ tech and picture thread. The inlet manifold and carby is of the Carry style, and the transfer case attached to the gearbox is definately not LJ, probably a 4x4 Carry, but I didn't think these were availble in the 2 stroke, only F5A efi?? Anyway, if it is tested as claimed to be, the engine itself will fit into a late LJ50 (Bellhousing bolt pattern changed between late '74/early '76) if you use your LJ50 inlet manifold and carb. Probably cheaper than a crank rebuild! |
|
| Author: | tonyevans [ Sun May 15, 2011 1:54 am ] |
| Post subject: | Re: 3 cyl 2 stroke motor |
Yes I saw that - a lot of bits missing too. |
|
| Author: | 303zuke [ Sun May 15, 2011 1:58 am ] |
| Post subject: | Re: 3 cyl 2 stroke motor |
Only the Starter Motor and Alt+bracket. |
|
| Author: | tonyevans [ Sun May 15, 2011 6:33 am ] |
| Post subject: | Re: 3 cyl 2 stroke motor |
Do you know what the gearbox is that it has bolted on in the picture? |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|