| auszookers.com https://auszookers.com/forum/ |
|
| WANTED: WT Jackshaft - NEVERMIND, GOT IT ALL https://auszookers.com/forum/viewtopic.php?f=8&t=32483 |
Page 1 of 1 |
| Author: | Scales [ Thu May 10, 2012 3:23 pm ] |
| Post subject: | WANTED: WT Jackshaft - NEVERMIND, GOT IT ALL |
Just chasing a WT Jackshaft guys so i can start on my sierra case swap. EDITED OUT ORIGINAL WANTS EDIT Got everything, thanks to all involved |
|
| Author: | dono1 [ Thu May 10, 2012 7:07 pm ] |
| Post subject: | Re: WT T-Case and Shafts for Jim conversion |
I have aWT transfer but there are noshafts or flanges |
|
| Author: | Scales [ Fri May 11, 2012 10:14 am ] |
| Post subject: | Re: WT T-Case and Shafts for Jim conversion |
anyone got one with flanges at the least? |
|
| Author: | Scales [ Tue May 15, 2012 9:41 am ] |
| Post subject: | Re: Widetrack Jackshaft & FWD shaft for Jimny conversion |
Bump. Just need shafts now guys. |
|
| Author: | BlueSuzy [ Tue May 15, 2012 11:36 am ] |
| Post subject: | Re: Widetrack Jackshaft & FWD shaft for Jimny conversion |
I have a front Jim shaft if wanted |
|
| Author: | Scales [ Tue May 15, 2012 11:41 am ] |
| Post subject: | Re: Widetrack Jackshaft & FWD shaft for Jimny conversion |
nope, Just WT mate. i have a Jimny remember so i already have the Jim front shaft.... |
|
| Author: | BlueSuzy [ Tue May 15, 2012 12:01 pm ] |
| Post subject: | Re: Widetrack Jackshaft & FWD shaft for Jimny conversion |
Is there much length difference between a jim front and a sierra front? Dont have one to compare. I only said if wanted.... |
|
| Author: | Fity [ Tue May 15, 2012 12:04 pm ] |
| Post subject: | Re: Widetrack Jackshaft & FWD shaft for Jimny conversion |
The front WT shaft is used in the rear of a Jimny when doing the T case conversion. Gets rid of the CV too. |
|
| Author: | Scales [ Tue May 15, 2012 12:28 pm ] |
| Post subject: | Re: Widetrack Jackshaft & FWD shaft for Jimny conversion |
oh is that where it goes fity? thanks for clearing it up, i thought it replaced the fwd shaft. what CV are you refferring to? Edit, just re-read monleys install, it makes sense now. |
|
| Author: | SierraDan [ Tue May 15, 2012 12:43 pm ] |
| Post subject: | Re: Widetrack Jackshaft & FWD shaft for Jimny conversion |
There's a CV joint rather than a uni on the rear shaft. I have a WT front shaft for sale. Good unis. Go fast orange. |
|
| Author: | Scales [ Tue May 15, 2012 12:46 pm ] |
| Post subject: | Re: Widetrack Jackshaft & FWD shaft for Jimny conversion |
Pm'ed ya now mate. Just had a squizz under the car. saw the CV, dont know how i ever missed that before now! so if i got this right, the front WT shaft goes in the back, and the WT jack stays in the jack position, front jim shaft stays the same. |
|
| Author: | Fity [ Wed May 16, 2012 11:40 am ] |
| Post subject: | Re: Widetrack Jackshaft & FWD shaft for Jimny conversion |
Scales wrote: Pm'ed ya now mate. Just had a squizz under the car. saw the CV, dont know how i ever missed that before now! so if i got this right, the front WT shaft goes in the back, and the WT jack stays in the jack position, front jim shaft stays the same. Sounds about right. |
|
| Author: | Scales [ Thu May 17, 2012 10:28 am ] |
| Post subject: | Re: Widetrack Jackshaft & FWD shaft for Jimny conversion |
Looks like i got a front shaft on the go from SierraDan. Anyone got a WT Jackshaft? |
|
| Author: | lordviper556 [ Fri May 18, 2012 11:26 am ] |
| Post subject: | Re: WT T-Case and Shafts for Jim conversion |
dono1 wrote: I have aWT transfer but there are noshafts or flanges do you still have it? |
|
| Author: | Scales [ Fri May 18, 2012 3:15 pm ] |
| Post subject: | Re: WANTED: Widetrack Jackshaft |
BUMP. Jackshaft only please... anyone? |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|