auszookers.com • View topic - WANTED: WT Jackshaft

Board index » Shift It And Find It » I Want it I Want it I want it

WANTED: WT Jackshaft - NEVERMIND, GOT IT ALL

Page 1 of 1

[ 15 posts ]

Print view

Previous topic | Next topic

Author

Message

Scales

az supporter

Joined: Mon May 30, 2011 9:28 am
Posts: 2233
Location: Townsville
Vehicle: 03 Jim M13A no-vvt, Vinyl Spec

Posted: Thu May 10, 2012 3:23 pm

Just chasing a WT Jackshaft guys so i can start on my sierra case swap.

EDITED OUT ORIGINAL WANTS

EDIT Got everything, thanks to all involved

_________________
MY BUILD THREAD HERE!!!!!

Last edited by Scales on Tue May 22, 2012 9:08 am, edited 6 times in total.

dono1

az supporter

Joined: Fri Nov 26, 2010 10:57 pm
Posts: 566
Location: Mid North Coast NSW

Posted: Thu May 10, 2012 7:07 pm

I have aWT transfer but there are noshafts or flanges

Scales

az supporter

Joined: Mon May 30, 2011 9:28 am
Posts: 2233
Location: Townsville
Vehicle: 03 Jim M13A no-vvt, Vinyl Spec

Posted: Fri May 11, 2012 10:14 am

anyone got one with flanges at the least?

_________________
MY BUILD THREAD HERE!!!!!

Scales

az supporter

Joined: Mon May 30, 2011 9:28 am
Posts: 2233
Location: Townsville
Vehicle: 03 Jim M13A no-vvt, Vinyl Spec

Posted: Tue May 15, 2012 9:41 am

Bump. Just need shafts now guys.

_________________
MY BUILD THREAD HERE!!!!!

BlueSuzy

az supporter

Joined: Sun May 04, 2008 11:30 pm
Posts: 9715
Location: NSW
Vehicle: SJ51 LWB, SJ70 SWB

Posted: Tue May 15, 2012 11:36 am

I have a front Jim shaft if wanted

_________________

BlueSuzy wrote:

I'm over the G16b's.

Scales

az supporter

Joined: Mon May 30, 2011 9:28 am
Posts: 2233
Location: Townsville
Vehicle: 03 Jim M13A no-vvt, Vinyl Spec

Posted: Tue May 15, 2012 11:41 am

nope, Just WT mate. i have a Jimny remember so i already have the Jim front shaft....

_________________
MY BUILD THREAD HERE!!!!!

BlueSuzy

az supporter

Joined: Sun May 04, 2008 11:30 pm
Posts: 9715
Location: NSW
Vehicle: SJ51 LWB, SJ70 SWB

Posted: Tue May 15, 2012 12:01 pm

Is there much length difference between a jim front and a sierra front? Dont have one to compare.

I only said if wanted....

_________________

BlueSuzy wrote:

I'm over the G16b's.

Fity

Joined: Sun Nov 07, 2010 11:58 pm
Posts: 148
Location: Sydney
Vehicle: Suzuki LJ50 & LJ81

Posted: Tue May 15, 2012 12:04 pm

The front WT shaft is used in the rear of a Jimny when doing the T case conversion. Gets rid of the CV too.

Scales

az supporter

Joined: Mon May 30, 2011 9:28 am
Posts: 2233
Location: Townsville
Vehicle: 03 Jim M13A no-vvt, Vinyl Spec

Posted: Tue May 15, 2012 12:28 pm

oh is that where it goes fity? thanks for clearing it up, i thought it replaced the fwd shaft. what CV are you refferring to?

Edit, just re-read monleys install, it makes sense now.

_________________
MY BUILD THREAD HERE!!!!!

Last edited by Scales on Tue May 15, 2012 1:02 pm, edited 1 time in total.

SierraDan

az supporter

Joined: Fri Feb 04, 2011 10:55 pm
Posts: 9348
Location: Newcastle
Vehicle: G13BB Jimny

Posted: Tue May 15, 2012 12:43 pm

There's a CV joint rather than a uni on the rear shaft.
I have a WT front shaft for sale. Good unis. Go fast orange.

_________________
mlm

Scales

az supporter

Joined: Mon May 30, 2011 9:28 am
Posts: 2233
Location: Townsville
Vehicle: 03 Jim M13A no-vvt, Vinyl Spec

Posted: Tue May 15, 2012 12:46 pm

Pm'ed ya now mate.

Just had a squizz under the car. saw the CV, dont know how i ever missed that before now!

so if i got this right, the front WT shaft goes in the back, and the WT jack stays in the jack position, front jim shaft stays the same.

_________________
MY BUILD THREAD HERE!!!!!

Fity

Joined: Sun Nov 07, 2010 11:58 pm
Posts: 148
Location: Sydney
Vehicle: Suzuki LJ50 & LJ81

Posted: Wed May 16, 2012 11:40 am

Scales wrote:

Sounds about right.

Scales

az supporter

Joined: Mon May 30, 2011 9:28 am
Posts: 2233
Location: Townsville
Vehicle: 03 Jim M13A no-vvt, Vinyl Spec

Posted: Thu May 17, 2012 10:28 am

Looks like i got a front shaft on the go from SierraDan. Anyone got a WT Jackshaft?

_________________
MY BUILD THREAD HERE!!!!!

lordviper556

Joined: Wed Oct 14, 2009 10:30 pm
Posts: 716
Location: sunny coast qld

Posted: Fri May 18, 2012 11:26 am

dono1 wrote:

I have aWT transfer but there are noshafts or flanges

do you still have it?

Scales

az supporter

Joined: Mon May 30, 2011 9:28 am
Posts: 2233
Location: Townsville
Vehicle: 03 Jim M13A no-vvt, Vinyl Spec

Posted: Fri May 18, 2012 3:15 pm

BUMP.
Jackshaft only please... anyone?

_________________
MY BUILD THREAD HERE!!!!!

Page 1 of 1

[ 15 posts ]

Board index » Shift It And Find It » I Want it I Want it I want it

Who is online

Users browsing this forum: No registered users and 10 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum