auszookers.com
https://auszookers.com/forum/

Any G series flywheel [Briz]
https://auszookers.com/forum/viewtopic.php?f=8&t=40207		 Page 1 of 1
Author:  JrZook [ Thu Apr 11, 2013 10:43 am ]
Post subject:  Any G series flywheel [Briz]
I got another fairly dangerous experiment on the mind 8)

It requires any G series flywheel with usable ring gear teeth. Do not care about the clutch face. So if anyone has one laying around taking up space I'd gladly take it off your hands :mrgreen:

Cheers Dan
Author:  boostedbrick [ Thu Apr 11, 2013 5:44 pm ]
Post subject:  Re: Any G series flywheel [Briz]
I reckon I have one attached to a motor at my folks place... I can have a look on Saturday.
Author:  JrZook [ Thu Apr 11, 2013 7:11 pm ]
Post subject:  Re: Any G series flywheel [Briz]
That would be sweet mate!
Author:  reeceh [ Thu Apr 11, 2013 7:40 pm ]
Post subject:  Re: Any G series flywheel [Briz]
I have a g16b flywheel downstairs. Came off my new motor. It's yours I can drop it off maybe tomorrow arvo after work?
Author:  JrZook [ Thu Apr 11, 2013 8:04 pm ]
Post subject:  Re: Any G series flywheel [Briz]
Yea? That would be great if you could! Cheers
Author:  reeceh [ Fri Apr 12, 2013 5:26 pm ]
Post subject:  Re: Any G series flywheel [Briz]
Are you home? Ill probaly slip past within the next hour
Author:  JrZook [ Sat Apr 13, 2013 12:36 am ]
Post subject:  Re: Any G series flywheel [Briz]
Cheers for dropping that off mate! I will go to an unintended home :D
Author:  reeceh [ Sat Apr 13, 2013 6:41 am ]
Post subject:  Re: Any G series flywheel [Briz]
All good!
Author:  2stroker [ Mon Apr 15, 2013 12:08 pm ]
Post subject:  Re: Any G series flywheel [Briz]
Ok Dan you have my attention, what are you up to
Author:  JrZook [ Mon Apr 15, 2013 4:39 pm ]
Post subject:  Re: Any G series flywheel [Briz]
Starter motor -> flywheel -> 200mm rollers = motorcycle roll starter! 8)
Author:  Red89 [ Mon Apr 15, 2013 7:08 pm ]
Post subject:  Re: Any G series flywheel [Briz]
JrZook wrote:
Starter motor -> flywheel -> 200mm rollers -> laptop = motorcycle dyno !! 8)

Armsup
Author:  JrZook [ Mon Apr 15, 2013 8:59 pm ]
Post subject:  Re: Any G series flywheel [Briz]
Red89 wrote:
JrZook wrote:
Starter motor -> flywheel -> 200mm rollers -> laptop = motorcycle dyno !! 8)

Armsup


Shhhhhhhhhhhhhh!! Please stop reading my mind :P

This should be good frame work for a dyno and fairly simple too. I have been on the look out for some small eddy current brakes 8) . Last dyno project I was playing with used a huge eddy current brake off some euro bus!
Author:  Damo [ Fri Apr 19, 2013 7:57 am ]
Post subject:  Re: Any G series flywheel [Briz]
JrZook wrote:
Red89 wrote:
JrZook wrote:
Starter motor -> flywheel -> 200mm rollers -> laptop = motorcycle dyno !! 8)

Armsup


Shhhhhhhhhhhhhh!! Please stop reading my mind :P

This should be good frame work for a dyno and fairly simple too. I have been on the look out for some small eddy current brakes 8) . Last dyno project I was playing with used a huge eddy current brake off some euro bus!


Gimme a yell when you're heading to the truck wreckers pompoms
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/