| Author |
Message |
strutts
Joined: Sat Jan 22, 2011 2:05 am Posts: 57 Location: Melbourne
|
 Posted: Thu Jul 07, 2011 11:31 pm |
|
|
wheres the engine numbers a on 1.6 motor? I cant find it!!!
|
|
|
|
 |
tanshi

az supporter
Joined: Tue Jan 09, 2007 10:30 pm Posts: 7717 Location: Brisbane
|
 Posted: Thu Jul 07, 2011 11:33 pm |
|
|
should be passenger side,
on the sloped bit where the gearbox meets the engine.
|
|
|
|
 |
strutts
Joined: Sat Jan 22, 2011 2:05 am Posts: 57 Location: Melbourne
|
 Posted: Thu Jul 07, 2011 11:33 pm |
|
sweeet thanks bud ill have a look 
|
|
|
|
 |
strutts
Joined: Sat Jan 22, 2011 2:05 am Posts: 57 Location: Melbourne
|
 Posted: Thu Jul 07, 2011 11:48 pm |
|
|
the only number on there is like 15**CM with a little 3 is that right :/
|
|
|
|
 |
zooky08

az supporter
Joined: Fri Nov 27, 2009 10:30 pm Posts: 3426 Location: imbil/gympie. qld
Vehicle: 03 Jimny
|
 Posted: Thu Jul 07, 2011 11:51 pm |
|
|
Should be were the bottom bolt hole for the engine to connect to the gear box
On the slope bit
_________________ 03 Jimny 30 km2s 75mm lift f&r locked winch
|
|
|
|
 |
strutts
Joined: Sat Jan 22, 2011 2:05 am Posts: 57 Location: Melbourne
|
 Posted: Thu Jul 07, 2011 11:57 pm |
|
|
how many numbers should it have? sorry i cant find it. and im tryin to get a rwc for it lol and coz its a 1.6 the old owner didnt give me the engine number :/
|
|
|
|
 |
tanshi

az supporter
Joined: Tue Jan 09, 2007 10:30 pm Posts: 7717 Location: Brisbane
|
 Posted: Thu Jul 07, 2011 11:59 pm |
|
|
if its a g16 it should start with g16 and then maybe 7-8 numbers?
|
|
|
|
 |
strutts
Joined: Sat Jan 22, 2011 2:05 am Posts: 57 Location: Melbourne
|
 Posted: Fri Jul 08, 2011 12:00 am |
|
|
passenger side yeh? the only number i can find is 1590cm3 which is jst the size yeh? lol so hard to find ><
|
|
|
|
 |
Reubs
Joined: Wed Sep 09, 2009 11:30 pm Posts: 1522 Location: Brisbane
Vehicle: SJ80, SE416
|
 Posted: Fri Jul 08, 2011 12:02 am |
|
strutts wrote: how many numbers should it have? sorry i cant find it. and im tryin to get a rwc for it lol and coz its a 1.6 the old owner didnt give me the engine number :/
Get some chalk maybe. It'll be stamped quite faintly.
Look at the big image here...
Last edited by Reubs on Fri Jul 08, 2011 12:05 am, edited 2 times in total.
|
|
|
|
 |
zooky08

az supporter
Joined: Fri Nov 27, 2009 10:30 pm Posts: 3426 Location: imbil/gympie. qld
Vehicle: 03 Jimny
|
 Posted: Fri Jul 08, 2011 12:02 am |
|
|
Should be 10 numbers/letters for g16
Look on engine just bellow timing plug on gear box
|
|
|
|
 |
strutts
Joined: Sat Jan 22, 2011 2:05 am Posts: 57 Location: Melbourne
|
 Posted: Fri Jul 08, 2011 12:04 am |
|
|
its all good i found it. thanks guys!!
|
|
|
|
 |
strutts
Joined: Sat Jan 22, 2011 2:05 am Posts: 57 Location: Melbourne
|
 Posted: Fri Jul 08, 2011 12:09 am |
|
it was covered in mud hense why i couldnt find it  lowest now have to pay an extra $200 for another bloody peice of paper coz the douche jst wrote down the old engine number, tried to book in at vicroads and they where like yeh thats wrong. haha fk 
|
|
|
|
 |
chillin24x7
Joined: Wed Sep 08, 2010 5:12 am Posts: 47 Location: Jimboomba
|
 Posted: Fri Jul 08, 2011 2:01 am |
|
|
you shouldnt have to repay as it was the inspector fault for not doing it right in the first place
|
|
|
|
 |
|