auszookers.com • View topic

Board index » Talking About Stuff » Suzuki Talk

Transfer removal

Page 1 of 1

[ 16 posts ]

Print view

Previous topic | Next topic

Author

Message

maloo11

Joined: Tue Jul 27, 2010 6:17 am
Posts: 232
Location: NSW

Posted: Fri Oct 15, 2010 5:38 am

In the process of taking out my transfer case (never done before). How do you get the small metal clamp off at the bottom of the lever? Does it split with a screwdriver?

_________________
91Sierra; 2in lift; 2inBL; 6.5s; 31muds;

Ben_Sierra

az supporter

Joined: Wed Sep 30, 2009 11:30 pm
Posts: 4472
Location: Perth

Posted: Fri Oct 15, 2010 5:47 am

Push down and twist.

_________________
I want my old sig back

Gwagensteve

Joined: Thu Feb 26, 2009 10:30 pm
Posts: 13007
Location: Melbourne

Posted: Fri Oct 15, 2010 5:57 am

Are you talking about the hose clamp thingy that holds the rubber boot on? if so, there is a little tab folded over that holds it tight. Find the tab and open it up with a screwdriver. (It's kind of a like a compressed Z shape and unfolds)

Steve.

maloo11

Joined: Tue Jul 27, 2010 6:17 am
Posts: 232
Location: NSW

Posted: Fri Oct 15, 2010 5:58 am

Ok. thanks

_________________
91Sierra; 2in lift; 2inBL; 6.5s; 31muds;

Last edited by maloo11 on Fri Oct 15, 2010 5:59 am, edited 1 time in total.

Gwagensteve

Joined: Thu Feb 26, 2009 10:30 pm
Posts: 13007
Location: Melbourne

Posted: Fri Oct 15, 2010 5:59 am

See my post above.

Steve.

maloo11

Joined: Tue Jul 27, 2010 6:17 am
Posts: 232
Location: NSW

Posted: Fri Oct 15, 2010 6:27 am

Ok guys, my shift lever aint moving. Boot is off and i can see the spring, everything done according to haynes manual, but the lever wont budge. i push down and turn and NOTHING. Does it need a helping hand with the hammer?

_________________
91Sierra; 2in lift; 2inBL; 6.5s; 31muds;

christover1

az supporter

Joined: Tue Jul 15, 2008 11:30 pm
Posts: 8203
Location: Melbourne
Vehicle: Pajero 91 NH 3.0 SWB

Posted: Fri Oct 15, 2010 6:33 am

I always left my stick on, when dropping t-case. It was easier to get at stick on the floor.
But make sure you push and twist on the bottom piece, not the stick itself

_________________
VIC ZOOK CLUB
http://www.vic.suzuki4wd.com/forum/

christover1

az supporter

Joined: Tue Jul 15, 2008 11:30 pm
Posts: 8203
Location: Melbourne
Vehicle: Pajero 91 NH 3.0 SWB

Posted: Fri Oct 15, 2010 6:41 am

See the bit in pic, will give you an idea how it comes out.
Same as the bit on a single stick, but didn't couldn't find a picture

_________________
VIC ZOOK CLUB
http://www.vic.suzuki4wd.com/forum/

maloo11

Joined: Tue Jul 27, 2010 6:17 am
Posts: 232
Location: NSW

Posted: Fri Oct 15, 2010 6:46 am

Got it. Thanks for your help.

_________________
91Sierra; 2in lift; 2inBL; 6.5s; 31muds;

Hotshot993

Joined: Wed Dec 01, 2010 9:46 pm
Posts: 1270
Location: Brisbane

Posted: Mon Sep 19, 2011 3:55 am

Hey my transfer lever is stuck in neutral. Trying to get that spring loaded thing off. I push down, turn anti clockwise. Should pop up all the way and stick should just pull out or what do I do. Been at it for last 30mins trying to twist it and get the thing off but nothing so far. Also it's really hard to twist that spring loaded thing.

stockman

az supporter

Joined: Thu Nov 05, 2009 10:30 pm
Posts: 5319
Location: Canberra
Vehicle: 4wd

Posted: Mon Sep 19, 2011 3:57 am

Just make sure you are pushing down hard enough.

Also when taking the case out I find it easier to leave the stick in and put it into 4x4 low.

_________________
Watch out or you'll get sued.

Hotshot993

Joined: Wed Dec 01, 2010 9:46 pm
Posts: 1270
Location: Brisbane

Posted: Mon Sep 19, 2011 4:01 am

I'm not taking the case out. Just need the stick out. And I got it turned a bit and it still won't pop up:/

Hotshot993

Joined: Wed Dec 01, 2010 9:46 pm
Posts: 1270
Location: Brisbane

Posted: Mon Sep 19, 2011 4:07 am

It like got to a certain part and t won't go any further. But won't pop up either

Hotshot993

Joined: Wed Dec 01, 2010 9:46 pm
Posts: 1270
Location: Brisbane

Posted: Mon Sep 19, 2011 4:11 am

Got it thanks. Just the spring wasn't pushing it up it was stuck.

stockman

az supporter

Joined: Thu Nov 05, 2009 10:30 pm
Posts: 5319
Location: Canberra
Vehicle: 4wd

Posted: Mon Sep 19, 2011 4:19 am

That was for the other guy.

Use a couple of flat head screwdrivers.

_________________
Watch out or you'll get sued.

Hotshot993

Joined: Wed Dec 01, 2010 9:46 pm
Posts: 1270
Location: Brisbane

Posted: Mon Sep 19, 2011 5:06 am

The problem is that it's like jammed between two gears and I need to try and line up the two gaps inside the transfer case so I get get the lever in there. If you kind of get what I mean:/

Page 1 of 1

[ 16 posts ]

Board index » Talking About Stuff » Suzuki Talk

Who is online

Users browsing this forum: No registered users and 66 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum