| Author |
Message |
|
bozzaa
|
 Posted: Sat Jun 02, 2012 12:30 pm |
|
|
also is there anyone on here, or can anyone reccommend someone I can pay to do my RUF setup. I am putting it in the too hard basket. I have a set off 33" swampers to go in so need someone with knowledge!
|
|
|
|
|
Trypt
Joined: Tue Apr 17, 2012 11:19 am Posts: 492
Vehicle: 1.3 Tin Top
|
Posted: Sat Jun 02, 2012 6:15 pm |
|
I have approached offroad shops about doing RUF conversion they wont touch it. due to legalities and getting it engineered. best bet will be an automotive engineer, or just a mate with a welder a grinder and some knowledge 
|
|
|
|
|
KEENSY85
Joined: Wed May 09, 2012 12:46 am Posts: 1742 Location: north brisbane
Vehicle: 1985 lwb sierra UTE
|
Posted: Sun Jun 03, 2012 4:46 pm |
|
|
That looks Like my nt but maybe Im looking at it wrong, sorry for hijacking but were do u get cromos from
_________________
Green? greeeen is nice !
|
|
|
|
|
|
bozzaa
|
Posted: Wed Aug 29, 2012 5:18 pm |
|
|
Hey guys I just paid Just_cruizn for a body kit, but my messages are hanging in my outbox and won't send! Is there anyone whom actually knows him that could let him know, or give me a phone number for him?
cheers!
|
|
|
|
|
|
bozzaa
|
Posted: Wed Aug 29, 2012 5:18 pm |
|
|
Hey guys I just paid Just_cruizn for a body lif kit, but my messages are hanging in my outbox and won't send! Is there anyone whom actually knows him that could let him know, or give me a phone number for him?
cheers!
|
|
|
|
|
atari4x4
az supporter
Joined: Mon Dec 11, 2006 10:30 pm Posts: 34842 Location: East Radelayed
Vehicle: SV420+SV620 Vitara's
|
Posted: Wed Aug 29, 2012 5:36 pm |
|
|
the messages will stay in your outbox until he's read them, he'll have it in the post asap going from my experience.
_________________
You're just hating because you don't understand
|
|
|
|
|
|
bozzaa
|
Posted: Wed Aug 29, 2012 5:40 pm |
|
|
thanks atari good to know
|
|
|
|
|
|
bozzaa
|
Posted: Wed Aug 29, 2012 5:46 pm |
|
|
thought i should update this thread while i am here. I have purchased a 1.6 for her, and a set off 33's. Progress has been held up due to engine blowing smoke and she wouldnt pass roady. I am going to drop the 1.6 in and 'hope' that the inspector doesn't notice its a different engine, he is happy to pass it the second he sees no smoke. Issue is that i need a body lift to fit her up, s lets hope he doesnt notice that! and if i put a bonnet scoop on to avoid lift, he will be asking questions i would think! will post photos of engine once in, should be over the next week or so
|
|
|
|
|
Zook_Fan
az supporter
Joined: Thu Mar 13, 2008 10:30 pm Posts: 4531 Location: Toowoomba
Vehicle: Maruti and LJ80's
|
Posted: Wed Aug 29, 2012 9:28 pm |
|
|
If that is all he is looking for try every oil additive you can find to see if you can stop it smoking just to get it through roadworthy then mod it. Doubt there'd be many mechanics out there that won't notice a body lift.
|
|
|
|
|
|
bozzaa
|
Posted: Thu Aug 30, 2012 7:36 am |
|
|
Mate she's running on pure stop smoke as she is. Starting to foul plugs overheat. Her time is up I think.
|
|
|
|
|
|
bozzaa
|
Posted: Thu Aug 30, 2012 6:05 pm |
|
|
I have just purcased a complete vitara with low kms. I am obviously pulling the engine out, but is there anything else anyone could reccommend i should be keeping off it? diffs, Diff centres etc.
|
|
|
|
|
dono1
az supporter
Joined: Fri Nov 26, 2010 10:57 pm Posts: 566 Location: Mid North Coast NSW
|
Posted: Thu Aug 30, 2012 6:17 pm |
|
|
Ill buy the front ring and pinion if you don't need it.
|
|
|
|
|
Ridge
Joined: Tue Jun 16, 2009 11:30 pm Posts: 942 Location: Brisbane
Vehicle: sierra leaf sprung buggy
|
Posted: Thu Aug 30, 2012 8:21 pm |
|
|
^^You can get extended rubber brake lines made up for $20 and braided lines from $30 at brake and clutch shops.
|
|
|
|
|
|
