auszookers.com • View topic - what part to grind

Board index » Talking About Stuff » Suzuki Talk

what part to grind

Page 1 of 1

[ 17 posts ]

Print view

Previous topic | Next topic

Author

Message

zooky08

az supporter

Joined: Fri Nov 27, 2009 10:30 pm
Posts: 3426
Location: imbil/gympie. qld
Vehicle: 03 Jimny

Posted: Mon Oct 11, 2010 7:46 am

hey i have a g16a bolted to a 1.3 gearbox with adapter plate
i havea a 1.3 starter motor as i didnt have time to fine a 1.6 starter motor

can ny one tell me or show me were you have to grind for it to fit.

heres a pic

much appreciated

Aaron

xedent

az supporter

Joined: Mon Jun 15, 2009 11:30 pm
Posts: 895
Location: Sunshine Coast, QLD
Vehicle: LWB Maruthi on WT Diffs!

Posted: Mon Oct 11, 2010 7:49 am

I would personally grind the starter rather then the block.

_________________
My Maruti build, Click WWW

Last edited by xedent on Mon Oct 11, 2010 7:50 am, edited 2 times in total.

zooktastic

Joined: Mon May 11, 2009 11:30 pm
Posts: 941
Location: west sydney

Posted: Mon Oct 11, 2010 7:50 am

x2 grind the starter motor's housing, did it on mine and works fine

zooky08

az supporter

Joined: Fri Nov 27, 2009 10:30 pm
Posts: 3426
Location: imbil/gympie. qld
Vehicle: 03 Jimny

Posted: Mon Oct 11, 2010 8:01 am

where on the starter do you grind nd how much do you grind off

Aaron

_________________
03 Jimny 30 km2s 75mm lift f&r locked winch

CairnsZook

az supporter

Joined: Tue Jul 18, 2006 11:30 pm
Posts: 872
Location: West Coast
Vehicle: Zookless

Posted: Mon Oct 11, 2010 8:13 am

Push the starter motor into position.
Rub it up and down against the engine block.
You should be able to see where it has contacted.
Start grinding...

I have to pull mine out again and grind off some more. It's making a pretty awful noise as the starter disengages

hooki

az supporter

Joined: Mon Jul 21, 2008 11:30 pm
Posts: 1785
Location: perth, WA
Vehicle: 85' LWB Sierra, 01' S15

Posted: Mon Oct 11, 2010 8:14 am

you grind the face of the starter that contacts the block. Do a little bit at a time with a flappa disc and check fitment every few passes with the grinder. Just make sure the starter sits in position properly.

_________________
79' LJ80 (sold) :(
95' & 97' sierra (sold)

Bruce

az supporter

Joined: Sun Jun 11, 2006 11:30 pm
Posts: 4003
Location: Brisbane

Posted: Mon Oct 11, 2010 8:14 am

Stick starter on, see where it's hitting (rubbing) grind a bit, check it, grind more till all is good.
There is no set measurement to take off because I'm guessing no-one would know, It's all suck and see.

_________________
[quote="royce"] I wouldnt mind insulating my rear

Bruce

az supporter

Joined: Sun Jun 11, 2006 11:30 pm
Posts: 4003
Location: Brisbane

Posted: Mon Oct 11, 2010 8:15 am

Bwhahahah 3 posts in about 1 min all saying the same thing. :-)

_________________
[quote="royce"] I wouldnt mind insulating my rear

CairnsZook

az supporter

Joined: Tue Jul 18, 2006 11:30 pm
Posts: 872
Location: West Coast
Vehicle: Zookless

Posted: Mon Oct 11, 2010 8:16 am

I hope we're not all wrong

Bruce

az supporter

Joined: Sun Jun 11, 2006 11:30 pm
Posts: 4003
Location: Brisbane

Posted: Mon Oct 11, 2010 8:16 am

LOL

_________________
[quote="royce"] I wouldnt mind insulating my rear

Bruce

az supporter

Joined: Sun Jun 11, 2006 11:30 pm
Posts: 4003
Location: Brisbane

Posted: Mon Oct 11, 2010 8:17 am

If only I could type faster I would have won. :-)

_________________
[quote="royce"] I wouldnt mind insulating my rear

zooky08

az supporter

Joined: Fri Nov 27, 2009 10:30 pm
Posts: 3426
Location: imbil/gympie. qld
Vehicle: 03 Jimny

Posted: Mon Oct 11, 2010 8:24 am

ok thanks guys ill wll try it tomorrow. hope you's are right :lol:

_________________
03 Jimny 30 km2s 75mm lift f&r locked winch

Bruce

az supporter

Joined: Sun Jun 11, 2006 11:30 pm
Posts: 4003
Location: Brisbane

Posted: Mon Oct 11, 2010 8:46 am

If it all goes to shit I'll delete my posts and blame all the others. LOL

_________________
[quote="royce"] I wouldnt mind insulating my rear

zooky08

az supporter

Joined: Fri Nov 27, 2009 10:30 pm
Posts: 3426
Location: imbil/gympie. qld
Vehicle: 03 Jimny

Posted: Mon Oct 11, 2010 8:56 am

Bruce wrote:

If it all goes to shit I'll delete my posts and blame all the others. LOL

absazooky-sierra

Joined: Tue May 11, 2010 5:34 am
Posts: 48
Location: maryvalley QLD

Posted: Mon Oct 11, 2010 9:23 am

your a beast how'd you go

zooky08

az supporter

Joined: Fri Nov 27, 2009 10:30 pm
Posts: 3426
Location: imbil/gympie. qld
Vehicle: 03 Jimny

Posted: Mon Oct 11, 2010 9:31 am

umm shit wasnt sitting straight so i got to do some grinding

_________________
03 Jimny 30 km2s 75mm lift f&r locked winch

mrw82

az supporter

Joined: Tue Jul 03, 2007 11:30 pm
Posts: 1350
Location: stuck in a hole. not off road, just deception bay.
Vehicle: snotbox, 84 LWB sierra 1 litre

Posted: Mon Oct 11, 2010 10:32 am

Bruce wrote:

If only I could type faster I would have won. :-)

you were lucky to be the sperm to win the race to the egg all those years ago..... I wouldn't get high hopes of ever winning anything else bruce!!!

Page 1 of 1

[ 17 posts ]

Board index » Talking About Stuff » Suzuki Talk

Who is online

Users browsing this forum: Beery and 60 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum