| Author |
Message |
Daves4wd

az supporter
Joined: Fri Aug 26, 2011 3:17 pm Posts: 1286 Location: Melbourne
Vehicle: Swb Sierra twin lock 32s 6.5s
|
 Posted: Thu Apr 05, 2012 10:53 pm |
|
Hey guys and girls I've got a 89 wt Sierra and I have a rattling sound coming from the the front right side I'm not to sure if its bearings there only a couple of months old except the king pin bearings and they stuffed up a couple weeks ago so they'll be getting or should I look at the spigot bearing? Thrust bearing even or a rooted clutch?? I hope I can find some help all these noises are shitting me up the wall  hahaha hope someone can shed some light on this thanks for reading and the help
|
|
|
|
 |
BlueSuzy

az supporter
Joined: Sun May 04, 2008 11:30 pm Posts: 9716 Location: NSW
Vehicle: SJ51 LWB, SJ70 SWB
|
 Posted: Thu Apr 05, 2012 11:51 pm |
|
|
if its the front right, I'd jack the whole front end up and check the wheel bearings. Wiggle the tyre from the top and bottom/push pull. You will then see if it is the kingpins again or wheel bearings. Both sides.
What size tyres/rim offset do you run?
_________________ BlueSuzy wrote: I'm over the G16b's.
|
|
|
|
 |
Daves4wd

az supporter
Joined: Fri Aug 26, 2011 3:17 pm Posts: 1286 Location: Melbourne
Vehicle: Swb Sierra twin lock 32s 6.5s
|
 Posted: Fri Apr 06, 2012 9:36 am |
|
|
I have play from top to bottom I'm running 30s and not to shore about offset thanks for that I'm pull it apart and see what I can find
|
|
|
|
 |
BlueSuzy

az supporter
Joined: Sun May 04, 2008 11:30 pm Posts: 9716 Location: NSW
Vehicle: SJ51 LWB, SJ70 SWB
|
 Posted: Fri Apr 06, 2012 9:52 am |
|
|
Ive had a kingpin collapse so the play was in the whole hub/knuckle assembly Also loose wheel bearings was the norm for mine.
You definatly have something going on. There should be no play.
_________________ BlueSuzy wrote: I'm over the G16b's.
|
|
|
|
 |
Daves4wd

az supporter
Joined: Fri Aug 26, 2011 3:17 pm Posts: 1286 Location: Melbourne
Vehicle: Swb Sierra twin lock 32s 6.5s
|
 Posted: Fri Apr 06, 2012 10:15 am |
|
|
Yer it's not to bad just noisy lol nah I reckon my kingpins are shagged and stuffing up my wheel bearings or maybe something else I just ordered a swivel hub rebuild kit off egay hopefully get it next week and do it then cheers for the help buddy Apprectiate it alot
|
|
|
|
 |
Daves4wd

az supporter
Joined: Fri Aug 26, 2011 3:17 pm Posts: 1286 Location: Melbourne
Vehicle: Swb Sierra twin lock 32s 6.5s
|
 Posted: Sat Apr 07, 2012 1:04 pm |
|
|
I think a part of my problem is my unis from the gearbox to tcase aswell there's little movement like 2 mm each way are all the unis the same?? Noob question I know but I'm just making sure thanks fr the help
|
|
|
|
 |
BlueSuzy

az supporter
Joined: Sun May 04, 2008 11:30 pm Posts: 9716 Location: NSW
Vehicle: SJ51 LWB, SJ70 SWB
|
 Posted: Sat Apr 07, 2012 2:40 pm |
|
|
you mean turning, 2mm backlash, or in the joint itself.
backlash is normal.
play in the joints are not.
_________________ BlueSuzy wrote: I'm over the G16b's.
|
|
|
|
 |
Daves4wd

az supporter
Joined: Fri Aug 26, 2011 3:17 pm Posts: 1286 Location: Melbourne
Vehicle: Swb Sierra twin lock 32s 6.5s
|
 Posted: Sat Apr 07, 2012 3:02 pm |
|
|
Play in the joints where the caps are backlash I'm not to fussed about lol
|
|
|
|
 |
BlueSuzy

az supporter
Joined: Sun May 04, 2008 11:30 pm Posts: 9716 Location: NSW
Vehicle: SJ51 LWB, SJ70 SWB
|
 Posted: Sat Apr 07, 2012 5:20 pm |
|
|
play in the joints is no good. replace asap.
_________________ BlueSuzy wrote: I'm over the G16b's.
|
|
|
|
 |
|