auszookers.com • View topic - rh inner cv or complete shaft from sv420 or sv620

Board index » Shift It And Find It » I Want it I Want it I want it

rh inner cv or complete shaft from sv420 or sv620

Page 1 of 1

[ 14 posts ]

Print view

Previous topic | Next topic

Author

Message

wombat178

Joined: Sat Jul 02, 2011 9:21 am
Posts: 92
Location: sunshine coast

Posted: Fri May 16, 2014 9:04 pm

hi im after a crownwheel from a 4.3 centre they have a 43 tooth count also after a rh inner cv to make a stubby shaft. Thanks in advance for any replys

Last edited by wombat178 on Mon May 19, 2014 1:56 pm, edited 1 time in total.

jdk81

Joined: Sat Jul 18, 2009 11:30 pm
Posts: 2372
Location: Ballarat, VIC

Posted: Fri May 16, 2014 10:31 pm

4.3...
front or rear?
Why only the crownwheel, and not the matched set (ring and pinion)

wombat178

Joined: Sat Jul 02, 2011 9:21 am
Posts: 92
Location: sunshine coast

Posted: Fri May 16, 2014 10:37 pm

Crap sorry rear wanting to try a mixture of gears hoping to run a 43 tooth cw with an 8 tooth pinion for 5.375 gears. Ive already got the front

Built4thrashing

Joined: Wed May 21, 2008 11:30 pm
Posts: 4972
Location: Dandenong .Vic
Vehicle: 1999 GV. Locked and Lifted

Posted: Sat May 17, 2014 8:06 am

wombat178 wrote:

Crap sorry rear wanting to try a mixture of gears hoping to run a 43 tooth cw with an 8 tooth pinion for 5.375 gears. Ive already got the front

good luck with that.

Zook_Fan

az supporter

Joined: Thu Mar 13, 2008 10:30 pm
Posts: 4530
Location: Toowoomba
Vehicle: Maruti and LJ80's

Posted: Sat May 17, 2014 8:08 am

Yeah... That's not going to work.

wombat178

Joined: Sat Jul 02, 2011 9:21 am
Posts: 92
Location: sunshine coast

Posted: Sat May 17, 2014 8:25 am

Ive got a 5.1cw and 4.3 pinion in a carrier right now with no binding wws kinda hoping it would work the other way .will put it together when I put my steel diff in and check tooth pattern etc

Zook_Fan

az supporter

Joined: Thu Mar 13, 2008 10:30 pm
Posts: 4530
Location: Toowoomba
Vehicle: Maruti and LJ80's

Posted: Sat May 17, 2014 8:34 am

If it doesn't bind straight away then you have lucked out and the pressure angles are similar enough to not feel it. I think you will still have problems with the pressure angle under power.

Gears are paired though, you shouldn't use a second hand gear from two different sets. It will cause premature wear and strength issues.

wombat178

Joined: Sat Jul 02, 2011 9:21 am
Posts: 92
Location: sunshine coast

Posted: Sat May 17, 2014 8:46 am

Yeah I know that but was just kinda hopeful it might work .... rh inner cv cup anyone??

Zook_Fan

az supporter

Joined: Thu Mar 13, 2008 10:30 pm
Posts: 4530
Location: Toowoomba
Vehicle: Maruti and LJ80's

Posted: Sat May 17, 2014 8:55 am

Just don't try it too far from home :lol:

do you want a gv or sv rh inner cup?

wombat178

Joined: Sat Jul 02, 2011 9:21 am
Posts: 92
Location: sunshine coast

Posted: Sat May 17, 2014 9:18 am

Gv i think arent they the higher spline count 26 i think. Imfigure if im going to the effort of putting the steel diff in and making a stubby shaft i might as well upgrade to the larger axle/spline count while im at it

Built4thrashing

Joined: Wed May 21, 2008 11:30 pm
Posts: 4972
Location: Dandenong .Vic
Vehicle: 1999 GV. Locked and Lifted

Posted: Sun May 18, 2014 6:53 pm

got heaps of GV ones but they wont clip into the Vitara centre. You want the 26 spline inner for a 95-97 SV420 / SV620 Vitara.

wombat178

Joined: Sat Jul 02, 2011 9:21 am
Posts: 92
Location: sunshine coast

Posted: Sun May 18, 2014 7:21 pm

If there was a 1530 lockright with the 26 spline couplers going in at the same time would this make a difference??

wombat178

Joined: Sat Jul 02, 2011 9:21 am
Posts: 92
Location: sunshine coast

Posted: Mon May 19, 2014 1:57 pm

Ok scratch crownwheel just after cv.... Anyone?

wombat178

Joined: Sat Jul 02, 2011 9:21 am
Posts: 92
Location: sunshine coast

Posted: Tue May 20, 2014 9:36 pm

Nothing??

Page 1 of 1

[ 14 posts ]

Board index » Shift It And Find It » I Want it I Want it I want it

Who is online

Users browsing this forum: No registered users and 20 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum