[Ben_Sierra]

is there anyone here in Perth that makes this kinda thing?

Freight from the east is almost as bad as freight from the States to here!

[shep]

steve wrote:

shep wrote:

steve wrote:

I might make one too, everyone will have one, except shep

bugger you lot, if no one wants the job i will get one from lowrange.

you might be better off, coz it no one here will make it within 2 years

i blame damo and his trend setting sierra build.

[nandor85]

lmfao i made my bull bar in 3 weeks im not that bad lmfao shouldnt be hard just have to work out mounting and reinforcment for the tow itch and rings

[nandor85]

just had the bumper bar off and my car and having a look u will have to build like a tow bar reinforcement behind the metal skin for the rear bumper and the only decent mounting points will be the towbar brackets and dropping bolts along the top of the bumper where ya normal 1s are just to keep it tidy

i have studyed the pic of the rear bumper and dont like the way it sits flt against the body on the sides would be fine for nt but wouldnt look right on the wt sierra cause of the gaurds etc so would be better if it was made to flush up to ya stock flares

i have a few pics quickly setched but i will do a final copy of the componants like the rear su[port behind the bumper the skin etc

[Ben_Sierra]

Ok, while we're all putting requests in, I'm just looking for something nice and simple...

Kinda like this but without the hoop on top...




Who can do that for me??

[nandor85]

u could make that yaself easy all u will have to do is get ya local pipe bender (i use aaa tubing here in adel) to bend the two pipes up for ya then it just welding ya braces in between and a plate back to ya chassi rail and capping off the end of the pipes and ya done u would have that made in 2-3hours at most

[Ben_Sierra]

Would be easy except.... I've never welded anything in my life, and I don't have a welder...

Other than that, no dramas...

[atari4x4]

Fatzook wrote:

atari4x4 wrote:

Polar_Bear wrote:

sierra only?.. what about one for vits?

x 4 for the SV420 Vitara's

Stuey, mike.knew, ninjamoses & myself... would be very interested along with a cradle to adapt an ARB winchbar...

Wouldn't the SV420 rear bar be the same as the 1.6? If so, I have a vit I can start modeling a bar off of. I'm just a little time poor at the moment trying to get a few other products off the ground.

Pete

Hey Pete,

this is the back of the SV420, all that steel on the back is part of the chassis & cant easily be removed!



Cheers
Gus

Sorry shep for the mega hi-jack of this thread...

[Fatzook]

atari4x4 wrote:

Fatzook wrote:

atari4x4 wrote:

Polar_Bear wrote:

sierra only?.. what about one for vits?

x 4 for the SV420 Vitara's

Stuey, mike.knew, ninjamoses & myself... would be very interested along with a cradle to adapt an ARB winchbar...

Wouldn't the SV420 rear bar be the same as the 1.6? If so, I have a vit I can start modeling a bar off of. I'm just a little time poor at the moment trying to get a few other products off the ground.

Pete

Hey Pete,

this is the back of the SV420, all that steel on the back is part of the chassis & cant easily be removed!



Cheers
Gus

Sorry shep for the mega hi-jack of this thread...

Thanks mate.









BTW, thats FUCKEN UGLY!!!!!

I'd need a close look at one to see where to start the mounts, but anything is possible. If there is a brisbanite with one I may be able to get something happening....

[paulv]

nandor85 wrote:

u could make that yaself easy all u will have to do is get ya local pipe bender (i use aaa tubing here in adel) to bend the two pipes up for ya then it just welding ya braces in between and a plate back to ya chassi rail and capping off the end of the pipes and ya done u would have that made in 2-3hours at most

Is aaa that that exhaust place on Deacon Ave in Richmond?

[atari4x4]

paulv wrote:

nandor85 wrote:

u could make that yaself easy all u will have to do is get ya local pipe bender (i use aaa tubing here in adel) to bend the two pipes up for ya then it just welding ya braces in between and a plate back to ya chassi rail and capping off the end of the pipes and ya done u would have that made in 2-3hours at most

Is aaa that that exhaust place on Deacon Ave in Richmond?

yeah, it was the old pacemaker factory from memory.

[Damo]

shep wrote:

steve wrote:

shep wrote:

steve wrote:

I might make one too, everyone will have one, except shep

bugger you lot, if no one wants the job i will get one from lowrange.

you might be better off, coz it no one here will make it within 2 years

i blame damo and his trend setting sierra build.

I'll build you one Shep

[shep]

Damo wrote:

shep wrote:

steve wrote:

shep wrote:

steve wrote:

I might make one too, everyone will have one, except shep

bugger you lot, if no one wants the job i will get one from lowrange.

you might be better off, coz it no one here will make it within 2 years

i blame damo and his trend setting sierra build.

I'll build you one Shep

good on ya damo ETA around 2018

[Damo]

shep wrote:

good on ya damo ETA around 2018

It's either that or get it from the Septics!

[shep]

Damo wrote:

shep wrote:

good on ya damo ETA around 2018

It's either that or get it from the Septics!

i think that that is what i am going to have to do 653us including delivery
for the bumper. i can sticky tape something onto it to hold the tyre.

whats the exchange rate at the moment?

[Ben_Sierra]

0.88USD = 1AUD

[steve]

shep wrote:

Damo wrote:

shep wrote:

good on ya damo ETA around 2018

It's either that or get it from the Septics!

i think that that is what i am going to have to do 653us including delivery
for the bumper. i can sticky tape something onto it to hold the tyre.

whats the exchange rate at the moment?

can ball make you one?

[Polar_Bear]

shep wrote:

whats the exchange rate at the moment?

you suck at the internet shep..

go to google and type

653 usd to aud

easy

[shep]

steve wrote:

shep wrote:

Damo wrote:

shep wrote:

good on ya damo ETA around 2018

It's either that or get it from the Septics!

i think that that is what i am going to have to do 653us including delivery
for the bumper. i can sticky tape something onto it to hold the tyre.

whats the exchange rate at the moment?

can ball make you one?

i am trying to talk ball into building me a kickarse g16 so i don't want to push
the issue especially now that he is actually doing some paid work

Polar_Bear wrote:

shep wrote:

whats the exchange rate at the moment?

you suck at the internet shep..

go to google and type

653 usd to aud

easy

thats pritty cool. thanks.

[shep]

653 U.S. dollars = 736.023445 Australian dollars

that is actually fairly good value. no one who is any good will charge less then
$80 per hour and i reckon there would have to be a days work at least in it.

[mcwilly]

That's awesome I might look into one aswell

[shep]

that is just for the rear bar the tyre carrier bit is another $982

[mcwilly]

I wouldn't want the tyre carrier anyway so isn't to bad

[shep]

i ended up buying one from low range. total cost was just under $1500.
it is very well made and looks as strong as.

[BUZOOKA]

aint u gonna have trouble getting to ur handle on tail gate with the wheel now beoing carried on the left ??

[want33s]

BUZOOKA wrote:

aint u gonna have trouble getting to ur handle on tail gate with the wheel now beoing carried on the left ??

Look a bit harder Buzzy

[BUZOOKA]

want33s wrote:

BUZOOKA wrote:

aint u gonna have trouble getting to ur handle on tail gate with the wheel now beoing carried on the left ??

Look a bit harder Buzzy

lol opps

lol i always look like an idiot so no reason here to be embarrased lol


didnt relise it was 2 peices

[Ben_Sierra]

Looks the goods.... Wish i could afford one...

[ZookiMonsta]

So wheres the fitted pics shep? Looks pretty flash

[shep]

ZookiMonsta wrote:

So wheres the fitted pics shep? Looks pretty flash

haha give me a chance mate. hopefully i will have it on this weekend.
just depends on if i go fishing or not.