| Author |
Message |
|
Shelby
|
 Posted: Thu Aug 20, 2009 1:23 am |
|
|
i hooked a battery up to the LJ the other day, brake lights work, reverse doesnt, cuz someone cuth the earth off and the right indicator works but when you flick it to the left it blinks once and freezes so the lights stay on except for front as it dont work at all.
Any idea's why it would freeze? bad earth etc....
Any suggestion would help. Cheers Shelby
|
|
|
|
 |
steak_knife

az supporter
Joined: Fri May 22, 2009 11:30 pm Posts: 21335 Location: Smart Ass Island
|
 Posted: Thu Aug 20, 2009 1:35 am |
|
|
Change the bulb that dosen`t work & try it again. If it`s bugged that is, take the bulb out & put a test light across the pole`s, if it lights up replace the bulb, if it dosen`t put 1 side of test light to earth, if it lights up you have a earth prob.
Hope that helps.
Steve
_________________ I used to be indecisive,
now I'm not so sure.....
|
|
|
|
 |
|
Shelby
|
 Posted: Thu Aug 20, 2009 1:39 am |
|
|
i took the bulb out, it looked fine and checked for continuety and it was ok
|
|
|
|
 |
steak_knife

az supporter
Joined: Fri May 22, 2009 11:30 pm Posts: 21335 Location: Smart Ass Island
|
 Posted: Thu Aug 20, 2009 1:49 am |
|
|
Check for power at the socket. the outer case is the earth, center pole positive.
_________________ I used to be indecisive,
now I'm not so sure.....
|
|
|
|
 |
jdk81
Joined: Sat Jul 18, 2009 11:30 pm Posts: 2372 Location: Ballarat, VIC
|
 Posted: Thu Aug 20, 2009 2:56 am |
|
|
The indicators run on the same line as the reverse light, so inspect that circuit.
I had an issue with a burnt out reverse gear switch, which caused my indicator circuit to do funny things and eventually blow the fuse, yet hazards worked fine.
|
|
|
|
 |
hutch

az supporter
Joined: Sun Nov 30, 2008 10:30 pm Posts: 1213 Location: SW Bris
|
 Posted: Thu Aug 20, 2009 8:06 pm |
|
|
might be the flasher unit?
|
|
|
|
 |
nissvit
Joined: Sun Apr 06, 2008 11:30 pm Posts: 184 Location: Brisbane
|
 Posted: Thu Aug 20, 2009 8:14 pm |
|
|
fix the front blinker.
depending on what flasher unit you've got, some need a certain amount of current to set the flashing rate. With the front bulb out there isn't enough current to get it to flash.
|
|
|
|
 |
bails

az supporter
Joined: Tue Aug 04, 2009 11:30 pm Posts: 131 Location: darwin
|
 Posted: Thu Aug 20, 2009 8:33 pm |
|
|
i second hutch.
i would be looking at your flasher unit. had kinda the same problem a couple weeks ago.mine would flash a couple of times then stay latched on.
just replaced the realy and it all work fine after that.
|
|
|
|
 |
shep
Joined: Thu Mar 29, 2007 11:30 pm Posts: 14498 Location: Here there everywhere
Vehicle: A manly awesome man jimny
|
 Posted: Thu Aug 20, 2009 10:12 pm |
|
bails wrote: i second hutch.
i would be looking at your flasher unit. had kinda the same problem a couple weeks ago.mine would flash a couple of times then stay latched on.
just replaced the realy and it all work fine after that.
i had to put a 25w resister on each direction to get it flashing right.
|
|
|
|
 |
|
Shelby
|
 Posted: Thu Aug 20, 2009 10:31 pm |
|
|
fixed it!:D bad earth on it and so now it works:D thanks for the help fella's, now i just gotta get the reverse light working, wired it up but still no go lol
|
|
|
|
 |
fourby

az supporter
Joined: Mon Aug 03, 2009 11:30 pm Posts: 440 Location: Brisvegas.
|
 Posted: Fri Aug 21, 2009 1:32 am |
|
/spotlight <interior switch/. should work 
_________________ 85 Holden Drover Soft top stocko.
[quote="losfer"
|
|
|
|
 |
|