| Author |
Message |
Trypt
Joined: Tue Apr 17, 2012 11:19 am Posts: 492
Vehicle: 1.3 Tin Top
|
 Posted: Sun May 20, 2012 1:05 pm |
|
|
I have a coolant leak on the back of the head as far as i can see, on the exhaust side. its been there since i bought it but has recently got a little worse. Coolant is dripping down the block and onto the bell housing. Does this mean new engine or head gasket maybe? should i try some chemiweld or similar
|
|
|
|
 |
Fatzook

az supporter
Joined: Sat Oct 27, 2007 11:30 pm Posts: 14977 Location: The Hills
Vehicle: Vitara, NGV
|
 Posted: Sun May 20, 2012 1:09 pm |
|
|
Make and model? Which engine?
_________________ 2013 GV 1998 SV420 ute
|
|
|
|
 |
Trypt
Joined: Tue Apr 17, 2012 11:19 am Posts: 492
Vehicle: 1.3 Tin Top
|
 Posted: Sun May 20, 2012 1:57 pm |
|
|
sierra 96 hard top 1.3 carb
|
|
|
|
 |
zooky08

az supporter
Joined: Fri Nov 27, 2009 10:30 pm Posts: 3426 Location: imbil/gympie. qld
Vehicle: 03 Jimny
|
 Posted: Sun May 20, 2012 3:29 pm |
|
|
Check the chock coolant hoses going into the back of the carby For leaks.
_________________ 03 Jimny 30 km2s 75mm lift f&r locked winch
|
|
|
|
 |
royce

omnipotent being
Joined: Sun Jun 11, 2006 11:30 pm Posts: 17216 Location: Pluto
|
 Posted: Sun May 20, 2012 3:49 pm |
|
|
I would check that it isnt a heater hose squirting it over there
Give it a clean and let it run up to temp to build some pressure and have a good look around with a mirror
|
|
|
|
 |
Trypt
Joined: Tue Apr 17, 2012 11:19 am Posts: 492
Vehicle: 1.3 Tin Top
|
 Posted: Sun May 20, 2012 6:05 pm |
|
|
It is definately dripping from the head behind the exhaust manifold flange. i will have a good look tomoro afternoon.
|
|
|
|
 |
royce

omnipotent being
Joined: Sun Jun 11, 2006 11:30 pm Posts: 17216 Location: Pluto
|
 Posted: Sun May 20, 2012 6:09 pm |
|
|
when you say behind, behind as in between manifold and firewall or between manifold and block?
|
|
|
|
 |
Trypt
Joined: Tue Apr 17, 2012 11:19 am Posts: 492
Vehicle: 1.3 Tin Top
|
 Posted: Sun May 20, 2012 6:21 pm |
|
|
between block and manifold. im guessing but looks like from between head and block
|
|
|
|
 |
Trypt
Joined: Tue Apr 17, 2012 11:19 am Posts: 492
Vehicle: 1.3 Tin Top
|
 Posted: Tue May 22, 2012 4:55 pm |
|
|
really odd but it seems to have stopped
|
|
|
|
 |
shandy92

az supporter
Joined: Tue Nov 25, 2008 10:30 pm Posts: 5066 Location: perth, Australia
|
 Posted: Tue May 22, 2012 6:31 pm |
|
Trypt wrote: really odd but it seems to have stopped maybe all the coolant has gone? if its still got coolant then there is no pressure to push it out. when its warm it will push it out again.
|
|
|
|
 |
Trypt
Joined: Tue Apr 17, 2012 11:19 am Posts: 492
Vehicle: 1.3 Tin Top
|
 Posted: Tue May 22, 2012 8:26 pm |
|
|
it used a small amount of water this morning then i topped it up before i came home. checked when i got home, i cant see any more coolant on the bell housing, the rad hoses definately had pressure in them and after letting it cool the water level has not dropped
|
|
|
|
 |
|