| Author |
Message |
wheelzie1989
Joined: Sun Jul 04, 2010 12:48 am Posts: 26 Location: hervey bay
|
 Posted: Mon Jul 05, 2010 7:31 am |
|
|
Hey all,
i had a search but nothing really came up, how well are the carby's on the 1990 Sierra's? i got the 1.3 engine and just wanting to know if imgoing to have to do some waterproofing on it to make it safe to go through big puddles
|
|
|
|
 |
PJ.zook

az supporter
Joined: Sat Oct 24, 2009 10:30 pm Posts: 845 Location: Melbourne
|
 Posted: Mon Jul 05, 2010 7:34 am |
|
|
The carby isnt youre issue as long as you have a snorkel, its the distributor that gets moisture inside it causing engine to run like a dog, and the solid engine fan that hydraulics in the water killing youre power.
|
|
|
|
 |
Fatzook

az supporter
Joined: Sat Oct 27, 2007 11:30 pm Posts: 14977 Location: The Hills
Vehicle: Vitara, NGV
|
 Posted: Mon Jul 05, 2010 7:40 am |
|
PJ.zook wrote: and the solid engine fan that hydraulics in the water killing youre power.
And it also chews the back of the radiator out.
_________________ 2013 GV 1998 SV420 ute
|
|
|
|
 |
wheelzie1989
Joined: Sun Jul 04, 2010 12:48 am Posts: 26 Location: hervey bay
|
 Posted: Mon Jul 05, 2010 8:01 am |
|
|
so in other words you can smack through some water, just dont bury it past the wheels in water?
|
|
|
|
 |
lordfury007
Joined: Mon Sep 28, 2009 11:30 pm Posts: 298 Location: Darwin, NT
|
 Posted: Mon Jul 05, 2010 8:13 am |
|
|
for your fan, if it electrically driven, install a switch so you can force the fan off when doing water crossings
for your distributor spray some good electrical waterproofing spray into prior to each crossing (once a day at most)
_________________ 1988 Suzuki Sierra (SJ50)
1.6L G16A (EFI) with Su
|
|
|
|
 |
MrRocky
Joined: Thu Dec 17, 2009 10:30 pm Posts: 4731 Location: perth
|
 Posted: Mon Jul 05, 2010 8:48 am |
|
|
buy a pair of rubber gloves and cut the finger tips off one and place it over your distributor running the spark plug leads through the finger holes and cable tie them up nice and tight (don't mix the leads up though) this will prevent some drama's. Also i covered the starter motor with a couple of plastic bags, duct tape and cable ties to protect the solenoid.
I also used a heap of silicon on the air intake pipes to make them water tight and there can also be a hole on the underside of the carby hat that can be plugged also. Then coat the hell out of everything with crc.
hope this helps, worked for me and my underwater adventures in the past.
NOTE: if the charcoal canister fills up with water your car will run like crap too.
_________________ ...
|
|
|
|
 |
hutch

az supporter
Joined: Sun Nov 30, 2008 10:30 pm Posts: 1213 Location: SW Bris
|
 Posted: Mon Jul 05, 2010 10:53 am |
|
|
_________________ 255 characters
|
|
|
|
 |
Gwagensteve
Joined: Thu Feb 26, 2009 10:30 pm Posts: 13007 Location: Melbourne
|
 Posted: Mon Jul 05, 2010 11:52 am |
|
wheelzie1989 wrote: so in other words you can smack through some water, just dont bury it past the wheels in water?
No, "smacking through" water is never a good idea.
When driving though water you want to be nice and smooth. Build a steady bow wave in front of the car. This will actually result in very little water in the engine bay. If you go too fast you'll drive through the bow wave, pushing lots of water through the engine bay and it will build against the firewall, flooding the electrics (if not the intake itself)
Lots of revs will drown the electrics too - the fan will spray water all over the engine.
The sierra is quite well designed for water crossings - even the intake is in a smart spot, but you have to drive appropriately.
Using a radiator blind is a good idea too.
In bog holes, I roll in very gently in 1st or 2nd low so I can feel if the car is hanging up on the diffs or loosing traction. I can make a call then to back out or ease further in. In a worst case scenario, I should mean I'm not a car length in stuck on both diffs with a non-running car.
Like most things, the best technique is rarely very spectacular.
Steve.
|
|
|
|
 |
MacDaddy

az supporter
Joined: Thu Mar 26, 2009 10:30 pm Posts: 10453 Location: Perth, Australia
Vehicle: Jeep
|
 Posted: Mon Jul 05, 2010 1:20 pm |
|
If you have to go through deep water... i was always told to tie a Tarp on the front... tie it under the bumper, then throw it back over the bonnet, tie it off, and away you go, easy... just try to keep a constant speed... 
|
|
|
|
 |
303zuke

az supporter
Joined: Wed Aug 19, 2009 11:30 pm Posts: 2447
Vehicle: LJ50V, SJ70
|
 Posted: Mon Jul 05, 2010 1:40 pm |
|
|
Fitting an electric fan is good advice with a override cutout switch (just remember to switch it back ON!), if not just loosen the fan belt before entering the water. The plastic fan can easily propel through the water and the blades will bend forward and rip into the radiator. Your charge light might come on the dash, but you've more than enough battery charge to see you across.
I seal the dizzy cap with a length of bluetack, then clamp the cap back on.
Try to not change gears or slip the clutch as water can get on the clutch linings and make it slip. Remember after leaving the water your brakes (inc handbrake) will be less effective being wet. Drive a short distance with the brake slightly applied to dry them out.
And just in case water does get in the cabin, put non-waterproof stuff up as high as possible (your lunch, clothing, UHF radio).
You do not have the required permissions to view the files attached to this post.
|
|
|
|
 |
fordem
Joined: Mon Apr 19, 2010 11:30 pm Posts: 2656 Location: Georgetown, Guyana
Vehicle: APK416, A6G415, A6N415
|
 Posted: Mon Jul 05, 2010 6:11 pm |
|
|
|
 |
lordfury007
Joined: Mon Sep 28, 2009 11:30 pm Posts: 298 Location: Darwin, NT
|
 Posted: Mon Jul 05, 2010 8:23 pm |
|
|
That video is awesome... I start losing courage when water starts coming over the bonnet... not when my head is almost underwater.
_________________ 1988 Suzuki Sierra (SJ50)
1.6L G16A (EFI) with Su
|
|
|
|
 |
hutch

az supporter
Joined: Sun Nov 30, 2008 10:30 pm Posts: 1213 Location: SW Bris
|
 Posted: Mon Jul 05, 2010 9:51 pm |
|
303zuke wrote: I seal the dizzy cap with a length of bluetack, then clamp the cap back on.
ahhaa, awesome 
_________________ 255 characters
|
|
|
|
 |
Red89
Joined: Tue Jan 12, 2010 10:30 pm Posts: 2801 Location: Perth
|
 Posted: Tue Jul 06, 2010 8:43 am |
|
303zuke wrote: Remember after leaving the water your brakes (inc handbrake) will be less effective being wet. Drive a short distance with the brake slightly applied to dry them out.
I nearly got run over by my own car on my first ever mud run
Pulled up on the other side of the bog hole, pulled on the hand brake and jumped out to watch everyone else. Next thing I know the car runs into my legs 
|
|
|
|
 |
skelaaleks
Joined: Wed Jun 09, 2010 8:31 am Posts: 237 Location: brissy
|
 Posted: Tue Jul 06, 2010 8:43 pm |
|
|
Number1 mod is extended breathers for your diffs etc
Without them your hot diff etc will cool rapidly and suck in all that great muddy water
|
|
|
|
 |
|