auszookers.com • View topic - jimny wheel bearing

Board index » Talking About Stuff » Suzuki Talk

jimny wheel bearing

Page 1 of 1

[ 21 posts ]

Print view

Previous topic | Next topic

Author

Message

smiffkid

az supporter

Joined: Fri Aug 13, 2010 12:55 pm
Posts: 3266
Location: perth wa

Posted: Tue Mar 08, 2011 8:47 am

is there a special tool needed to tighten or remove wheel bearings,ours need tightening

steak_knife

az supporter

Joined: Fri May 22, 2009 11:30 pm
Posts: 21335
Location: Smart Ass Island

Posted: Tue Mar 08, 2011 8:57 am

They are a cassette bearing, can't be tightened as the pre-load is set, you need to replace said bearing..
Unless it's started to wear the stub axle a lil bit, than you can tighten, a lil bit.

_________________
I used to be indecisive,
now I'm not so sure.....

smiffkid

az supporter

Joined: Fri Aug 13, 2010 12:55 pm
Posts: 3266
Location: perth wa

Posted: Tue Mar 08, 2011 9:29 am

cheers
ill ring suzi store tomorrow and get some newbies

_________________
dodgy brothers mechanical

steak_knife

az supporter

Joined: Fri May 22, 2009 11:30 pm
Posts: 21335
Location: Smart Ass Island

Posted: Tue Mar 08, 2011 9:38 am

http://www.auszookers.com/index.php?nam ... rofile=377

he should be able to get you some....

_________________
I used to be indecisive,
now I'm not so sure.....

smiffkid

az supporter

Joined: Fri Aug 13, 2010 12:55 pm
Posts: 3266
Location: perth wa

Posted: Tue Mar 08, 2011 9:53 am

yea but id have to wait to get them over,
if i was in no rush id deffinitly ask him
need the car for the weekend that is all

_________________
dodgy brothers mechanical

89_tintop

az supporter

Joined: Fri Aug 07, 2009 11:30 pm
Posts: 3159
Location: gold coast

Posted: Tue Mar 08, 2011 9:58 am

so is there a special tool to undo em? and do em back up ?? more so on the do em back up as I am guessing they need to be torqued or something

_________________
http://auszookers.com/index.php?name=Forums&file=v

BAZZOOK

Joined: Sat Mar 24, 2007 10:30 pm
Posts: 1052
Location: MORNINGTON. VIC

Posted: Tue Mar 08, 2011 7:28 pm

you'll need one of these. BenT across the bug duch sells em for about $70.00. they tighten to about 220nm I think.

You do not have the required permissions to view the files attached to this post.

lordviper556

Joined: Wed Oct 14, 2009 10:30 pm
Posts: 716
Location: sunny coast qld

Posted: Tue Mar 08, 2011 7:32 pm

i got one of those from him off ebay. the wheel bearings are pretty easy to do when you have that socket.

did mine in a couple of hours taking it very easy.

http://www.bigjimny.com/images/document ... arings.pdf

Benz

Joined: Mon Oct 27, 2008 10:30 pm
Posts: 1006
Location: Cervantes WA

Posted: Tue Mar 08, 2011 10:47 pm

I was going to do my wheel bearings when I replaced my cv and freshened up the front end but it's f@#$ing hard without the tool...

will do it another time when I have the tool =]

haha I know where the extra seal I got goes now =]

steak_knife

az supporter

Joined: Fri May 22, 2009 11:30 pm
Posts: 21335
Location: Smart Ass Island

Posted: Wed Mar 09, 2011 5:52 am

Hammer & punch, I never had a "special tool" at the dealership & I had lot's of bearing apart..

_________________
I used to be indecisive,
now I'm not so sure.....

atari4x4

az supporter

Joined: Mon Dec 11, 2006 10:30 pm
Posts: 34842
Location: East Radelayed
Vehicle: SV420+SV620 Vitara's

Posted: Wed Mar 09, 2011 6:07 am

steak_knife wrote:

Hammer & punch, I never had a "special tool" at the dealership & I had lot's of bearing apart..

Don't sell yourself short Stekky, you are the "suzuki special tool"

_________________
You're just hating because you don't understand

Benz

Joined: Mon Oct 27, 2008 10:30 pm
Posts: 1006
Location: Cervantes WA

Posted: Wed Mar 09, 2011 6:14 am

atari4x4 wrote:

steak_knife wrote:

Hammer & punch, I never had a "special tool" at the dealership & I had lot's of bearing apart..

Don't sell yourself short Stekky, you are the "suzuki special tool"

haha yeah i was going to do that. didn't want to break something and be car-less...

wasn't sure if i would be able to get it tight enough again too....

meh

steak_knife

az supporter

Joined: Fri May 22, 2009 11:30 pm
Posts: 21335
Location: Smart Ass Island

Posted: Wed Mar 09, 2011 6:25 am

Benz2369 wrote:

atari4x4 wrote:

steak_knife wrote:

Hammer & punch, I never had a "special tool" at the dealership & I had lot's of bearing apart..

Don't sell yourself short Stekky, you are the "suzuki special tool"

haha yeah i was going to do that. didn't want to break something and be car-less...

wasn't sure if i would be able to get it tight enough again too....

meh

Cheer's Gus, I think... :lol:

You can get em tight enough, but having the tool would make the job a hell of a lot easier..
good luck busting a retaining ring to.... :lol:

_________________
I used to be indecisive,
now I'm not so sure.....

weaves

az supporter

Joined: Fri Mar 21, 2008 10:30 pm
Posts: 1564
Location: Newcastle

Posted: Wed Mar 09, 2011 8:45 am

smiffkid wrote:

yea but id have to wait to get them over,
if i was in no rush id deffinitly ask him
need the car for the weekend that is all

For future reference, i airbag everything, so overnight between all major centres, 2 to 3 for those that live in the middle of bumfark no where

weaves

_________________
I'm Weaver & i like beer, boobs, cars and stickers

Taylor74

Joined: Fri Dec 24, 2010 10:26 am
Posts: 198
Location: Perth WA

Posted: Wed Mar 09, 2011 10:03 am

steak_knife wrote:

Hammer & punch, I never had a "special tool" at the dealership & I had lot's of bearing apart..

_________________
Suzuki is my way of life.

smiffkid

az supporter

Joined: Fri Aug 13, 2010 12:55 pm
Posts: 3266
Location: perth wa

Posted: Wed Mar 09, 2011 10:32 am

maybe i should of got 1 of those tools,
how much r they,

_________________
dodgy brothers mechanical

BenT

az supporter

Joined: Sun Nov 16, 2008 10:30 pm
Posts: 208
Location: Nelson, NZ
Vehicle: 85 SJ413

Posted: Thu Mar 10, 2011 12:33 am

smiffkid wrote:

maybe i should of got 1 of those tools,
how much r they,

$64AU + $10 shipping. See here for pics:

http://www.auszookers.com/index.php?nam ... ic&t=15009

Ben

_________________
WWW.ZUKPARTS.COM - Quality Suzuki Off-road Parts

zukenutter

az supporter

Joined: Sun Feb 08, 2009 10:30 pm
Posts: 9045
Location: Brisneyland
Vehicle: 2006 Jimny JLX

Posted: Thu Mar 10, 2011 10:20 am

I bought the tool a while back, still haven't used it though. Good to have in the kit.

_________________
Click WWW below for STICKERS

smiffkid

az supporter

Joined: Fri Aug 13, 2010 12:55 pm
Posts: 3266
Location: perth wa

Posted: Thu Mar 10, 2011 10:42 am

i might have to get 1, ill pm u a bit later

_________________
dodgy brothers mechanical

Moag

az supporter

Joined: Thu Mar 04, 2010 10:30 pm
Posts: 411
Location: Kununurra WA ^ Top End
Vehicle: 2001 Jimny M13A

Posted: Thu Mar 10, 2011 12:22 pm

I brought one of BenT and have used it.
Quality tool that makes the job sooo easy!!!

BAZZOOK

Joined: Sat Mar 24, 2007 10:30 pm
Posts: 1052
Location: MORNINGTON. VIC

Posted: Fri Mar 11, 2011 6:05 am

zukenutter wrote:

I bought the tool a while back, still haven't used it though. Good to have in the kit.

me too. handy to have just in case.

Page 1 of 1

[ 21 posts ]

Board index » Talking About Stuff » Suzuki Talk

Who is online

Users browsing this forum: Google [Bot], Google Adsense [Bot] and 442 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum