auszookers.com • View topic - gears popping out after body lift

Board index » Talking About Stuff » Suzuki Talk

gears popping out after body lift

Page 1 of 1

[ 18 posts ]

Print view

Previous topic | Next topic

Author

Message

DomGat

Joined: Tue May 17, 2011 1:02 pm
Posts: 111
Location: Sydney

Posted: Wed Jul 20, 2011 9:54 pm

2nd and 4th gear keep popping out after I installed a 2" body lift & 40mm suspension lift.
Any ideas what's causing it & is there an easy fix?

Gwagensteve

Joined: Thu Feb 26, 2009 10:30 pm
Posts: 13007
Location: Melbourne

Posted: Wed Jul 20, 2011 10:02 pm

Impossible! Never heard of it!

Have you done a search? This has been covered countless times. You need to open up the shifter hole in the floor.

Steve

sogone

az supporter

Joined: Mon Oct 25, 2010 11:29 am
Posts: 2070
Location: Darwin

Posted: Wed Jul 20, 2011 10:25 pm

Grimbo'd ^^

DomGat

Joined: Tue May 17, 2011 1:02 pm
Posts: 111
Location: Sydney

Posted: Wed Jul 20, 2011 10:32 pm

No worries fellas, my bad.

smiffkid

az supporter

Joined: Fri Aug 13, 2010 12:55 pm
Posts: 3266
Location: perth wa

Posted: Wed Jul 20, 2011 10:52 pm

your gear lever may be hitting the floor, few ways to fix it, cut the hole bigger or even hit the floor down,
or bend the lever, we had the same problem

_________________
dodgy brothers mechanical

stockman

az supporter

Joined: Thu Nov 05, 2009 10:30 pm
Posts: 5319
Location: Canberra
Vehicle: 4wd

Posted: Wed Jul 20, 2011 11:30 pm

Here's a link that may help:

http://www.auszookers.com/index.php?nam ... pping+gear

_________________
Watch out or you'll get sued.

matt91112011

Joined: Fri Feb 11, 2011 9:05 am
Posts: 241
Location: Eltham, Victoria

Posted: Thu Jul 21, 2011 2:37 am

Gear lever is hitting the floor mate, I just put a 2" body lift in mine and had the same issue. I wouldn't cut into the body. I'd bend and extend your gear levers 2"s, you'll have the same issue with your transfer case lever.

Cheers

Matty

zooktastic

Joined: Mon May 11, 2009 11:30 pm
Posts: 941
Location: west sydney

Posted: Thu Jul 21, 2011 3:56 am

get a heat torch and bend the buggers, once this was done i had no problems

Reubs

Joined: Wed Sep 09, 2009 11:30 pm
Posts: 1522
Location: Brisbane
Vehicle: SJ80, SE416

Posted: Thu Jul 21, 2011 4:38 am

On my coily with 2" body lift the problem isn't the gear stick hitting the cutout, it's the tension the rubber boot creates when it is bolted in place. Unbolt it (I stuck mine back in a new position with race tape), and there is no problem. Also I have no problem with the transfer lever - the lever just has to be pushed against the limits of the cutout but it still functions fine.

jimbo_jones

az supporter

Joined: Sat Jul 19, 2008 11:30 pm
Posts: 4361
Location: gong
Vehicle: 2015 Jimny, LJ50, Maruti

Posted: Thu Jul 21, 2011 6:19 am

loosen your body mounts and push the body forward on the chassie

_________________
www.illawarrasuzuki4wdclub.webs.com

bagnkat

az supporter

Joined: Sun Aug 16, 2009 11:30 pm
Posts: 346
Location: Port Stephens.
Vehicle: SJ80

Posted: Thu Jul 21, 2011 6:26 am

Reubs wrote:

On my coily with 2" body lift the problem isn't the gear stick hitting the cutout, it's the tension the rubber boot creates when it is bolted in place.

x2 about the rubber boot on a coily.

stockman

az supporter

Joined: Thu Nov 05, 2009 10:30 pm
Posts: 5319
Location: Canberra
Vehicle: 4wd

Posted: Thu Jul 21, 2011 6:51 am

jimbo_jones wrote:

loosen your body mounts and push the body forward on the chassie

That would make it worse.

_________________
Watch out or you'll get sued.

sogone

az supporter

Joined: Mon Oct 25, 2010 11:29 am
Posts: 2070
Location: Darwin

Posted: Thu Jul 21, 2011 9:30 am

With mine we just turned the rubber boot around and put a slight bend in the lever. Makes it perfect.

Gwagensteve

Joined: Thu Feb 26, 2009 10:30 pm
Posts: 13007
Location: Melbourne

Posted: Thu Jul 21, 2011 9:47 am

I'm not a fan of bent gearlevers.

Steve.

alien

Joined: Wed Mar 24, 2010 10:30 pm
Posts: 16343
Location: Perth
Vehicle: '92 Sierra, 1.6efi, SPOA, 31s.

Posted: Thu Jul 21, 2011 9:57 am

do a transfer lift =)

_________________

Jester

Joined: Fri May 08, 2009 11:30 pm
Posts: 726
Location: Adelaide
Vehicle: 1985 Suzuki MightyBoy

Posted: Thu Jul 21, 2011 11:25 am

I sorted it on my vit with 2in lift bending the gearstick about 70deg and putting in backwards! perfect

dp87

Joined: Fri Jun 04, 2010 11:48 am
Posts: 174
Location: sydney

Posted: Fri Jul 22, 2011 5:40 am

same i just took my shifter stick out put in in a vice and bent it. had to use a pipe to make it a bit easier to bend. didnt have to bend it too much. saves cutting your car up

jimbo_jones

az supporter

Joined: Sat Jul 19, 2008 11:30 pm
Posts: 4361
Location: gong
Vehicle: 2015 Jimny, LJ50, Maruti

Posted: Fri Jul 22, 2011 7:17 am

stockman wrote:

jimbo_jones wrote:

loosen your body mounts and push the body forward on the chassie

That would make it worse.

well push the body the other way :roll:

_________________
www.illawarrasuzuki4wdclub.webs.com

Page 1 of 1

[ 18 posts ]

Board index » Talking About Stuff » Suzuki Talk

Who is online

Users browsing this forum: Google [Bot] and 847 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum